REAR NO. 1 SEAT ASSEMBLY (for RH Side): Installation

WARNING: This page is about a different car, the 2007 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL REAR NO. 1 SEAT ASSEMBLY RH (w/o Rear No. 2 Seat)
1. Fully tilt the seatback forward.
2. Place the seat in the cabin.
  NOTE: Be careful not to damage the vehicle body.
3. Connection procedures of seat to lock cable when reusing seat:
  1. Using a screwdriver, detach the claw and remove the connector case from the seat.
    HINT:
    
    Tape the screwdriver tip before use.
    
    Fig 1: Connecting Connector Case From Seat
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Install the connector case to the body's cap.
    
    Fig 2: Installing Connector Case To Body'S Cap
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. Pull out the joint piece. Align the slits of the joint piece and connector case.
    
    Fig 3: Aligning Slits Of Joint Piece And Connector Case
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. Compress the spring of the adjuster, and pull out the cable from the seat's cap.
    HINT:
    
    Perform this procedure with the lock of the adjuster released.
    
    Fig 4: Compressing Spring Of Adjuster
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. Install the seat cable's end part to the connector case's slit.
    
    Fig 5: Installing Seat Cable'S End Part To Connector Case'S Slit
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    
    HINT:
    
    Position the joint piece cable's end part as shown in the illustration.
    
    Fig 6: Positioning Joint Piece Cable'S
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. Install the seat's cap to the connector case.
  7. Temporarily place the seat into the vehicle where it will be installed.
    
    Fig 7: Installing Seat'S Cap To Connector Case
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. Return the seatback to the upright position.
    
    Fig 8: Returning Seatback To Upright Position
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. Attach the claws of the connector and adjuster, and install them to the seat.
    
    Fig 9: Connecting Connector And Adjuster
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. Press the adjuster's lock piece to lock it.
    NOTE: When pressing the lock piece, make sure the adjuster's spring is not compress.
    
    Fig 10: Pressing Lock Piece
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connection procedures of seat to lock cable when replacing seat:
  1. Cut the joint piece on the lock cable, and remove it.
    HINT:
    - A joint piece is included with new seats.
    - This procedure is not necessary when the lock cable is replaced with a new one.
  2. Temporarily place the seat into the vehicle where it will be installed.
    
    Fig 11: Connecting Lock Cable
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. Install the body's cap to the connector case.
    
    Fig 12: Installing Body'S Cap To Connector Case
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. Press the adjuster's lock pin.
    
    Fig 13: Pressing Adjuster'S Lock Pin
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. Return the seatback to the upright position.
    
    Fig 14: Returning Seatback To Upright Position
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. Press the adjuster's lock piece to lock it.
    NOTE: When pressing the lock piece, make sure the adjuster's spring is not compressed.
5. Lift up the seat track adjusting handle and move the seat to the foremost position.
  
  Fig 15: Pressing Lock Piece
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Tighten the 2 bolts on the rear side of the seat.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  HINT:
  
  Tighten the bolts in the order indicated in the illustration.
7. Lift up the seat track adjusting handle and move the seat to the rearmost position.
  
  Fig 16: Tightening Bolts On Rear Side Of Seat
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Tighten the 2 bolts on the front side of the seat.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  HINT:
  
  Tighten the bolts in the order indicated in the illustration.
INSTALL REAR NO. 1 SEAT ASSEMBLY RH (w/Rear No. 2 Seat)
1. Fully tilt the seatback forward.
2. Place the seat in the cabin.
  NOTE: Be careful not to damage the vehicle body.
  
  Fig 17: Tightening Bolts On Front Side Of Seat
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Return the seatback to the upright position.
4. Lift up the seat track adjusting handle and move the seat to the foremost position.
  
  Fig 18: Returning Seatback To Upright Position
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Tighten the 2 bolts on the rear side of the seat.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  HINT:
  
  Tighten the bolts in the order indicated in the illustration.
6. Lift up the seat track adjusting handle and move the seat to the rearmost position.
  
  Fig 19: Tightening Bolts On Rear Side Of Seat
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Tighten the 2 bolts on the front side of the seat.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  HINT:
  
  Tighten the bolts in the order indicated in the illustration.
  
  Fig 20: Tightening Bolts On Front Side Of Seat
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/o Rear No. 2 Seat)
1. Attach the clamps and install the cable to the vehicle body.
  
  Fig 21: Attaching Clamps And Cable To Vehicle Body
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEAT LEG COVER
1. Attach the 8 claws to install the 2 leg covers.
  
  Fig 22: Installing Rear Seat Leg Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR NO. 3 SEAT LEG SIDE COVER (w/Rear No. 2 Seat)
1. Attach the 4 claws to install the rear No. 3 seat leg side cover.
  
  Fig 23: Installing Rear No. 3 Seat Leg Side Cover (W/Rear No. 2 Seat)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR NO. 3 SEAT LEG SIDE COVER (w/o Rear No. 2 Seat)
1. Attach the 4 claws to install the No. 3 rear seat leg side cover.
  
  Fig 24: Installing Rear No. 3 Seat Leg Side Cover (W/O Rear No. 2 Seat)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR NO. 2 SEAT LEG SIDE COVER
1. Attach the 3 claws and clip to install the rear No. 2 seat leg side cover.
INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (w/o Rear No. 2 Seat)
1. Connect the rear No. 1 seat lock cable to the lever.
  
  Fig 25: Installing Rear No. 2 Seat Leg Side Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the lever with the 2 bolts.
  Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf)
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY (w/o Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )

Fig 26: Installing Lever With Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL RECLINING REMOTE CONTROL LEVER BEZEL RH (w/o Rear No. 2 Seat)
1. Attach the 6 claws to install the bezel.
INSTALL REAR FLOOR FINISH PLATE (w/o Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL BACK DOOR WEATHERSTRIP (w/o Rear No. 2 Seat)
INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (w/o Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL REAR FLOOR NO. 3 BOARD (w/o Rear No. 2 Seat)
INSTALL REAR FLOOR NO. 2 BOARD (w/o Rear No. 2 Seat)
INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)

Fig 27: Attaching Claws To Bezel
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR FLOOR NO. 1 BOARD (w/o Rear No. 2 Seat)
INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)
INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/o Rear No. 2 Seat)