Transmission Control Cable Assembly: Replacement

WARNING: This page is about a different car, the 2008 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.

REMOVE REAR CONSOLE BOX SUB-ASSEMBLY
1. Remove the console box (see REMOVAL ).
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
REMOVE BATTERY
1. Loosen the nut and remove the bolt and battery clamp.
2. Remove the battery.
3. Remove the battery tray.
4. Remove the 4 bolts and battery carrier.
5. Remove the 2 bolts and battery bracket reinforcement.
REMOVE AIR CLEANER ASSEMBLY
1. Disconnect the mass air flow meter connector.
2. Remove the 2 clamps of the engine wire.
  
  Fig 1: Identifying Engine Wire Clamps
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Remove the 4 bolts from the air cleaner case.
4. Disconnect the air cleaner case from the No. 1 air cleaner inlet.
REMOVE TRANSAXLE CONTROL CABLE ASSEMBLY
1. Remove the nut and disconnect the control cable from the control shaft lever.
  
  Fig 3: Identifying Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove the clip and disconnect the control cable from the control cable bracket.
  
  Fig 4: Identifying Control Cable Clip
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Disconnect the control cable from the control cable support.
  
  Fig 5: Identifying Control Cable Support
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Remove the bolt and disconnect the damp of the control cable.
  
  Fig 6: Identifying Damp Of Control Cable Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Disconnect the control cable from the shift lever.
  
  Fig 7: Identifying Control Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Turn the nut and disconnect the control cable from the shift lever retainer.
  
  Fig 8: Identifying Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Remove the 2 bolts and control cable.
  
  Fig 9: Identifying Control Cable Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY
1. Install the control cable with the 2 bolts.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
  
  Fig 10: Identifying Control Cable Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Turn the nut of the control cable and push in the lock.
  
  Fig 11: Identifying Nut Of Control Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the control cable onto the shift lever retainer.
  
  Fig 12: Identifying Control Cable Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  NOTE:
  - Install the cable with the protruding portion of the cable outer facing upward.
  - After installing, check that the lock of the cable outer is protruding beyond portion A-A, as shown in the illustration.
    
    Fig 13: Identifying Cable With Protruding Portion Of Cable Outer
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the control cable to the shift lever.
  NOTE: Connect the control cable so that the adjusting mechanism lock of the control cable is installed oh the driver side of the vehicle.
  
  Fig 14: Identifying Control Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Fix the control cable onto the control cable bracket with the clip.
  
  Fig 15: Identifying Control Cable Clip
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Connect the control cable onto the control shaft lever with the nut.
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
  
  Fig 16: Identifying Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Connect the clamp of the control cable with the bolt.
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
  
  Fig 17: Identifying Damp Of Control Cable Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Connect the control cable to the cable support.
INSTALL AIR CLEANER ASSEMBLY
1. Connect the air cleaner case to the No. 1 air cleaner inlet.
2. Install the air cleaner case with the 4 bolts.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
  
  Fig 19: Identifying Air Cleaner Case Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Connect the 2 clamps of the engine wire.
4. Connect the mass air flow meter connector.
INSTALL BATTERY
1. Install the battery bracket reinforcement with the 2 bolts.
  Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
2. Install the battery carrier with the 4 bolts.
  Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
3. Install the battery tray.
4. Connect the 2 clamps of the engine wire.
5. Install the battery with the battery clamp.
  Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) for bolt
  
  5.0 N*m (51 kgf*cm, 44 in.*lbf) for nut
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
INSPECT SHIFT LEVER POSITION
1. When shifting the lever from P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.
2. Start the engine and make sure that the vehicle moves forward when shifting the lever from N to the D position and moves rearward when shifting the lever to the R position.
  If the operation cannot be performed as specified, inspect the park/neutral position switch and check the shift lever installation condition.
ADJUST SHIFT LEVER POSITION (See ADJUSTMENT )
INSTALL REAR CONSOLE BOX SUB-ASSEMBLY
1. Install the rear console box (see INSTALLATION ).