REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door): Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Always use "Torx" socket wrench E10 when installing the rear seat.

HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.

Fig 1: Identifying Seat Belt Hole Seal Claws

INSTALL SEAT BELT HOLE SEAL
1. Engage the 2 claws and install the seat belt hole seal.
  
  Fig 2: Identifying Seat Belt Hole Seal Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEAT OUTER BELT ASSEMBLY
1. Check the angle of inclination required to lock the retractor.
  1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.
    NOTE: Do not disassemble the retractor.
    
    If the operation is not as specified, replace the rear seat outer belt.
    
    Fig 3: Identifying Inclination Angle Of For Locking Retractor
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.
  Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
  
  Fig 4: Locating Hooks And Retractor Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the through anchor with the bolt.
  Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
4. Check that the ELR locks.
  NOTE: Perform the check with the rear seat outer belt installed.
  1. With the belt installed, check that the belt locks when it is pulled out quickly.
    If the operation is not as specified, replace the rear seat outer belt.
    
    Fig 5: Locating Anchor Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL ROOF SIDE INNER GARNISH
1. for RH Side (w/ Curtain Shield Airbag):
  1. Install a new special clip.
  2. Pass the rear seat outer and rear center seat outer belts through the slit in the roof side inner garnish.
  3. Engage the 4 clips and the claw and install the roof side inner garnish.
    
    Fig 6: Identifying Roof Side Inner Garnish RH Clips And Claws - W/O Curtain Shield Airbag
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. for RH Side (w/o Curtain Shield Airbag):
  1. Pass the rear seat outer and rear center seat outer belts through the slit in the roof side inner garnish.
  2. Engage the 4 clips and the claw and install the roof side inner garnish.
    
    Fig 7: Identifying Roof Side Inner Garnish LH Clips And Claws - W/ Curtain Shield Airbag
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. for LH Side (w/ Curtain Shield Airbag):
  1. Install a new special clip.
  2. Pass the rear seat outer belt through the slit in the roof side inner garnish.
  3. Engage the 4 clips and the claw and install the roof side inner garnish.
    
    Fig 8: Identifying Roof Side Inner Garnish LH Clips And Claws - W/O Curtain Shield Airbag
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. for LH Side (w/o Curtain Shield Airbag):
  1. Pass the rear seat outer belt through the slit in the roof side inner garnish.
  2. Engage the 4 clips and the claw and install the roof side inner garnish.
INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side) (See INSTALLATION )

Fig 9: Identifying Rear Roof Side Rail Garnish Clips
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL DECK TRIM SIDE PANEL ASSEMBLY
1. for RH Side:
  1. Engage the 3 clips and the 3 claws and install the deck trim side panel.
  2. Tighten the 3 screws.
    
    Fig 10: Identifying Deck Side Room Light Connector Clips And Claws
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. for LH Side:
  1. Connect the luggage compartment room light connector.
  2. Engage the 3 clips and the 3 claws and install the deck trim side panel.
  3. Tighten the 3 screws.
    
    Fig 11: Identifying Seat Belt Anchor Cover Cap Claws
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Engage the clip and install the anchor plate of the rear seat outer belt.
4. Tighten the bolt.
  Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
INSTALL REAR DECK TRIM COVER (See INSTALLATION )

Fig 12: Locating Deck Trim Side Panel Assembly Clips, Claws And Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY
1. Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.
  
  Fig 13: Identifying Anchor Plate Clip
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEAT SHOULDER BELT HANGER
1. Engage the 2 claws and install the rear seat shoulder belt hanger.
  
  Fig 14: Identifying Rear Seat Shoulder Belt Hanger Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the belt of the rear seat outer belt.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP (See INSTALLATION )
INSTALL FRONT DOOR SCUFF PLATE (See INSTALLATION )
INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type)
1. for RH Side:
  1. Install the rear seat assembly INSTALLATION .
2. for LH Side:
  1. Install the rear seat assembly (See INSTALLATION ).
    
    Fig 15: Identifying Front Quarter Trim Panel Clips, Claws And Retainer
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 REAR SEAT LEG COVER (for 60/40 Split Seat Type LH Side) (See INSTALLATION )
INSTALL NO. 1 REAR SEAT LEG COVER (for 60/40 Split Seat Type)
1. for RH Side:
  1. Install the No. 1 rear seat leg cover INSTALLATION .
2. for LH Side:
  1. Install the No. 1 rear seat leg cover (See INSTALLATION ).
INSTALL REAR SEATBACK ASSEMBLY (for Hold Down Seat Type) INSTALLATION
INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hold Down Seat Type) INSTALLATION
INSTALL DECK FLOOR BOX
1. for RH Side:
  1. Install the deck floor box (See INSTALLATION ).
2. for LH Side:
  HINT:
  
  Use the same procedure as for the RH side.
INSTALL DECK BOARD SUB-ASSEMBLY (See INSTALLATION )
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (See INSTALLATION )
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for LH Side)
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)