Front Stabilizer Bar: Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL FRONT STABILIZER BAR BUSH
1. Install the stabilizer bar bush to the stabilizer bar.
  HINT:
  - Install the bush onto the stabilizer so that the bush stopper of the stabilizer bar faces the outside of the vehicle.
  - Install the bush with its cutout facing the front of the vehicle.
    
    Fig 1: Installing Front Stabilizer Bar Bush
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT STABILIZER BAR
1. Install the stabilizer onto the crossmember with the paint mark on the left side of the vehicle.
  
  Fig 2: Installing Front Stabilizer Bar
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT STABILIZER BRACKET LH
1. Provisionally tighten bolt A.
2. Tighten the bolts to the specified torque, in the order of B then A.
  Torque: 47 N.m (479 kgf*cm, 35 ft.*lbf)
INSTALL FRONT STABILIZER BRACKET RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.

Fig 3: Locating Front Stabilizer Bracket RH Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL POWER STEERING GEAR (See INSTALLATION )
INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (See INSTALLATION )
INSTALL FRONT STABILIZER LINK ASSEMBLY LH
1. Install the stabilizer link with the 2 nuts.
  HINT:
  
  If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
INSTALL FRONT STABILIZER LINK ASSEMBLY RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.

Fig 4: Locating Stabilizer Link Nuts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT LOWER SUSPENSION ARM LH (See INSTALLATION )
INSTALL FRONT LOWER SUSPENSION ARM RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL TIE ROD END SUB-ASSEMBLY LH (See INSTALLATION )
INSTALL TIE ROD END SUB-ASSEMBLY RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY (See INSTALLATION )
INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY (See INSTALLATION )
INSTALL COLUMN HOLE COVER SILENCER SHEET (See INSTALLATION )
INSTALL FRONT WHEEL
Torque: 103 N.m (1,050 kgf*cm, 76 ft.*lbf)
POSITION WHEELS FACING STRAIGHT AHEAD
INSTALL OUTER COWL TOP PANEL
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY (for Hatchback) (See INSTALLATION )
INSTALL FRONT AIR SHUTTER SEAL (for Sedan) (See INSTALLATION )
INSTALL FRONT WIPER MOTOR AND LINK
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback) (See extxref document="A00299887" filetype="sgml" extrefid="S17343015002008092700000">INSTALLATION )
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL HOOD TO COWL TOP SEAL (for Hatchback) (See INSTALLATION )
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan) (See INSTALLATION )
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan) (See INSTALLATION )
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL FRONT WIPER ARM HEAD CAP
Hatchback: (See INSTALLATION )

Sedan: (See INSTALLATION )
INSPECT HOOD
Hatchback: (See ADJUSTMENT )

Sedan: (See ADJUSTMENT )
ADJUST HOOD
Hatchback: See ADJUSTMENT

Sedan: See ADJUSTMENT
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque: 5.4 N.m (55 kgf*cm, 48 in.*lbf)
INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (See ADJUSTMENT )