FRONT WIPER MOTOR (for Sedan): Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL FRONT WIPER MOTOR
1. Install the front wiper motor with the 3 bolts.
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
  
  Fig 1: Identifying Front Wiper Motor Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Apply DENSO No. 50 grease to the crank arm pivot of the front wiper motor.
3. Install the rod onto the crank arm pivot of the front wiper motor.
  
  Fig 2: Locating Crank Arm Pivot
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT WIPER MOTOR AND LINK
1. Connect the connector.
2. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
3. Install the front wiper motor and link with the 2 bolts.
  Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
  
  Fig 3: Identifying Front Wiper Motor And Link Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
1. Connect the washer hoses.
2. Engage the 5 hooks.
  
  Fig 4: Identifying Cowl Top Ventilator Louver Sub-Assembly Hooks
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Engage the 8 hooks and the 4 claws.
4. Install the cowl top ventilator louver sub-assembly with the 3 clips.
  
  Fig 5: Identifying Cowl Top Ventilator Louver Sub-Assembly Hooks, Claws And Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH
1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
Fig 6: Identifying Cowl Side Ventilator Sub-Assembly Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH
HINT:

Use the same procedure as for the LH side.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
2. Clean the wiper pivot serrations with a wire brush.
3. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
4. Align the blade tip with the mark on the windshield glass, as shown in the illustration.
5. Tighten the nut of the front wiper arm.
  Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf)
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
2. Clean the wiper pivot serrations with a wire brush.
3. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
4. Align the blade tip with the mark on the windshield glass, as shown in the illustration.
5. Tighten the nut of the front wiper arm.
  Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf)
INSTALL FRONT WIPER ARM HEAD CAP
1. Engage the claw and install the 2 front wiper arm head caps.
Fig 11: Identifying Front Wiper Arm Head Cap Position
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)