LEMON Manuals: Even more car manuals for everyone
Home >> Smart >> 2015 >> Fortwo Electric Drive, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 90 (Propeller Shaft - 212 Chassis) >> Testing & Repair >> Replace centering sleeve - AR41.10-P-0200CW

Replace centering sleeve - AR41.10-P-0200CW

WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.

MODEL 172, 204, 207, 212, 218, 231 

Shown on front half of propeller shaft 

Fig 1: Centering Sleeve - Shown On Front Half Of Propeller Shaft
G09976506Courtesy of MERCEDES-BENZ USA
REMOVINGINSTALLING Remove/install     
1 Remove propeller shaft MODEL 172 AR41.10-P-0050V
MODEL 204, 207 AR41.10-P-0050CW
MODEL 212, 218 AR41.10-P-0050EW 
MODEL 231 AR41.10-P-0050RK
2 Separate propeller shaft at the slide connection   AR41.10-P-0050-05TX 
INSTALLATION IMPORTANT Coat splined profile with long-life grease and connect front half of propeller shaft (1) and rear half of propeller shaft.  
Long-life grease *BR00.45-Z-1001-06A 
INSPECT Check     
3 Check centering sleeve (10) in front half of propeller shaft (1) and rear half of propeller shaft If the sealing lip in the centering sleeve (10) is worn or damaged, the centering sleeve (10) must be replaced.
Remove centering sleeve (10)		  
Removal of centering sleeve
Press in centering sleeve (10).		 AR41.10-P-0200-02TX 
Press in guide sleeve
MODEL 172		 AR41.10-P-0200-03W
Press in guide sleeve
MODEL 204, 207, 212, 218, 231		 AR41.10-P-0200-03TX 
MODEL 172 *BE41.10-P-1001-02E 
MODEL 204, 207, 212, 218 *BE41.10-P-1001-02M 
MODEL 231 *BE41.10-P-1001-04A 
4 Fill cavities of both centering sleeves (10) with grease MB multipurpose grease *BR00.45-Z-1017-06A 
5 Install in the reverse order    
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE

Number Designation MODEL 172.447/448 MODEL 172.403/457
BE41.10-P-1001-02E Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 23, 3 24, 8
Rear propeller shaft mm 26, 8 28, 3
-   - -
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE

Number Designation MODEL 172.475
BE41.10-P-1001-02E Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 22, 4
Rear propeller shaft mm 25, 9
-   -
CHECK VALUES FOR PROPELLER SHAFT PILOT BUSHING

Number Designation MODEL 231.457 MODEL 231.473/479
BE41.10-P-1001-04A Press-in dimension "a" from face end of pilot bushing to joint flange Front propeller shaft mm 24, 8 25, 3
Rear propeller shaft mm 28, 3 28, 8
CHECK VALUES FOR PROPELLER SHAFT PILOT BUSHING

Number Designation MODEL 231.474
BE41.10-P-1001-04A Press-in dimension "a" from face end of pilot bushing to joint flange Front propeller shaft mm 25, 3
Rear propeller shaft mm 36, 2
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 204.001/201 MODEL 204.000/002/200/202
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 24, 8 24, 8
Rear propeller shaft mm 36, 2 36, 3
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation With autom. transmission Model 204.006/007/041/044/045/046/048/049/052/054/081/082/085/087/089/092/207/241/245/246/248/249/252/254/282/289/292/981/982/983/984/987/992
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 24, 8 23, 3
Rear propeller shaft mm 36, 2 26, 8
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 204.008/047/056/065/208/247/256/901/902/956 MODEL 204.022/025/222/225
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 24, 8 25, 3
Rear propeller shaft mm 28, 3 28, 8
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 204.077/277 With manual transmission
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 28, 8 25, 3
Rear propeller shaft mm 28, 8 36, 2
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 207.302/402 MODEL 207.303/403
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 24, 8 25, 3
Rear propeller shaft mm 36, 3 36, 2
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 207.322/372/422/472 MODEL 207.347/356/357/447/456/457
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 25, 3 24, 8
Rear propeller shaft mm 28, 8 28, 3
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 207.348/448 MODEL 212.002/005/202/205
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 23, 3 24, 8
Rear propeller shaft mm 26, 8 36, 3
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation With autom. transmission MODEL 212.047/093/247/293
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 25, 3 24, 8
Rear propeller shaft mm 36, 2 28, 3
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 212.041/048/054/082/087/089/090/147/148/248/254/282/287/288/289 MODEL 212.053/056/057/256/257
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 23, 3 36, 3
Rear propeller shaft mm 26, 8 28, 3
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation With manual transmission MODEL 212.154
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 25, 3 34, 8
Rear propeller shaft mm 28, 8 26, 8
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 218.303/323/373 MODEL 218.359 without CODE 460 (Additional parts, Canadian vehicles) without CODE 494 (US version)
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 25, 3 36, 3
Rear propeller shaft mm 28, 8 28, 3
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE

Number Designation MODEL 218.359 with CODE 460 (Additional parts, Canadian vehicles) with CODE 494 (US version) MODEL 218.391 MODEL 218.374
BE41.10-P-1001-02M Press-in dimension "a" from face end of centering sleeve to joint flange Front propeller shaft mm 24, 8 25, 3
Rear propeller shaft mm 28, 3 36, 2
REPAIR MATERIALS

Number Designation Order number
BR00.45-Z-1001-06A Long-life grease A 000 989 63 51 11
BR00.45-Z-1017-06A MB multipurpose grease A 001 989 34 51 11
scientia non olet · About LEMON Manuals