Press in guide sleeve - AR41.10-P-0200-03TX
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.
MODEL 204, 207, 212, 218, 219, 231
CHECK VALUES FOR DRIVE SHAFT CENTERING SLEEVE
| Number | Designation | Model 219.354 | Model 219.322/372 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02L | Insertion dimension "a" from face end of centering sleeve to joint flange | Front drive shaft | mm | 23, 3 | 25, 3 |
| Rear drive shaft | mm | 26, 8 | 28, 8 |
CHECK VALUES FOR DRIVE SHAFT CENTERING SLEEVE
| Number | Designation | Model 219.356/357/375/ 376/377 | ||
|---|---|---|---|---|
| BE41.10-P-1001-02L | Insertion dimension "a" from face end of centering sleeve to joint flange | Front drive shaft | mm | 24, 8 |
| Rear drive shaft | mm | 28, 3 |
CHECK VALUES FOR PROPELLER SHAFT PILOT BUSHING
| Number | Designation | Model 231.457 | Model 231.473/479 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04A | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 3 | 28, 8 |
CHECK VALUES FOR PROPELLER SHAFT PILOT BUSHING
| Number | Designation | Model 231.474 | ||
|---|---|---|---|---|
| BE41.10-P-1001-04A | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 25, 3 |
| Rear propeller shaft | mm | 36, 2 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 204.001/201 | Model 204.000/002/200/202 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 24, 8 |
| Rear propeller shaft | mm | 36, 2 | 36, 3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | With autom. transmission | Model 204.006/007/041/044/045/046/048/049 /052/054/081 /082/085/087 /089/092/207 /241/245/246 /248/249/252 /254/282/289 /292/981/982 /983/984/987 /992 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 23, 3 |
| Rear propeller shaft | mm | 36, 2 | 26, 8 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 204.008/047/056/065/208/247/256/901/902/ 956 | Model 204.022/025/222/225 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 3 | 28, 8 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 204.077/277 | With manual transmission | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 28, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 8 | 36, 2 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 207.302/402 | Model 207.303/403 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 36, 3 | 36, 2 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 207.322/372/422/472 | Model 207.347/356/357/447/456/457 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 24, 8 |
| Rear propeller shaft | mm | 28, 8 | 28, 3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 207.348/448 | Model 212.002/005/202/205 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 23, 3 | 24, 8 |
| Rear propeller shaft | mm | 26, 8 | 36, 3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | With autom. transmission | Model 212.047/093/247/293 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 24, 8 |
| Rear propeller shaft | mm | 36, 2 | 28, 3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 212.041/048/054/082/087/089/090/147/148/248/254/282/287/288/289 | Model 212.053/056/057/256/257 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 23, 3 | 36, 3 |
| Rear propeller shaft | mm | 26, 8 | 28, 3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | With manual transmission | MODEL 212.154 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 34, 8 |
| Rear propeller shaft | mm | 28, 8 | 26, 8 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 218.303/323/373 | Model 218.359 without CODE 460 (Additional parts, Canadian vehicles) without CODE 494 (US version) | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 36, 3 |
| Rear propeller shaft | mm | 28, 8 | 28, 3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 218.359 with CODE 460 (Additional parts, Canadian vehicles) with CODE 494 (US version) Model 218.391 |
Model 218.374 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 3 | 36, 2 |
- Use a suitable drift to drive in the new guide sleeve. MODEL 231, 204, 207, 212, 218, 219
Observe press-in dimension (a) from the end face of the centering sleeve to the flange.
The specified press-in distance (a) may deviate depending on the thickness of the flexible couplings, e.g. in vehicles with vibration damper. In these cases the dimension (a) measured prior to removal should be used for installation.