6X Body - Equipment Outside - General

• WM 6X00IN Disposal of airbag and seat-belt pretensioner units
  • Tools
  • Disposal of airbag and seat-belt pretensioner units
  • Safety procedures when igniting airbag units
  • Tools and materials
    • Detonator (ignition device) 9257
    • Adapter cable 9257/4
    • Adapter cable 9257/7
    • Adapter cable 9257/6
    • Ignition cable 9257/1
  • Connecting ignition tool
    • Driver's side
    • Passenger's side
    • Side airbag
    • Adapter cable 9257/6
    • Head airbag
    • Seat-belt pretensioners
    • Ignition module for front lid
    • Knee airbag
    • Pyrotechnical cutoff relay
• WM 6X00IN General information on removing car windows
  • Technical values
  • Cutting force for removing glass with cutting thread
  • Removing glass
    • Removing glass with VAS 861 001 A
    • Removing glass with VAS 1474 B
  • Tools
  • Tools and materials
  • Removing glass with cutting-wire separating device
  • Cutting force for removing glass with cutting wire
• WM 6X00IN Handling and replacing airbag and seat-belt pretensioner units
  • Tools
  • Tools and materials
    • Materials
  • General warning notes
    • General warnings for handling airbag and seat-belt pretensioner units
    • Warnings about assembly and straightening work
  • Information for handling airbag and seat-belt pretensioner units
    • Dangers for persons and the environment
    • Protective measures and rules of behavior
    • Behavior in cases of malfunction or danger
    • General information
    • Replacing components after airbag/seat-belt pretensioner triggering
• WM 6X00IN Technical values
  • Technical values
    • Overview
    • Technical values -63- Front apron
    • Technical values -63- Rear panel
    • Technical values -63- Rear apron
    • Technical values -63- Front retaining strip
    • Technical values -63- Rear retaining strip
    • Technical values -63- Front bumper
    • Technical values -63- Front carrier
    • Technical values -64- Glazing, window control
    • Technical values -66- Rear spoiler
    • Technical values -66- Rear wheel covers
    • Technical values -66- Rear-view mirror
    • Technical values -66- Covers
    • Technical values -68- Glove compartment
    • Technical values -68- Grab handles
    • Technical values -68- Front door sill trim
    • Technical values -68- Rear door sill trim
    • Technical values -68- Front ashtray
    • Technical values -68- Dashboard trim panel
    • Technical values -68- Centre console
    • Technical values -68- Oddments tray lid
    • Technical values -68- Seat
    • Technical values -69- Sun blind
    • Technical values -69- Passenger's airbag
    • Technical values -69- Belt guide
    • Technical values -69- Pedestrian protection
    • Technical values -66- Trailer hitch
    • Technical values - front seat belt system
    • Technical values - rear seat belt system
    • Technical values -68- Centre bearing for sun visor
    • Technical values -68- Front cupholder
  • Technical values -60- Sliding roof, slide/tilt sunroof
• WM 6X00IN22 Processing of Porsche 2-component window adhesive
  • Tools
  • Technical values
  • General information
    • Version
    • Safety data sheet
    • Shelf life
    • Disposal
    • Bonding log
  • Porsche 2-component window adhesive in body building
  • Working with Porsche 2-component window adhesive
    • General information
    • Preparing vehicle window - old window on which adhesive has already been applied
    • Preparing vehicle window - new vehicle window
    • Preparing body/window flange - old paintwork
    • Preparing body/window flange - new paintwork
    • Processing conditions
    • Joining process
    • Hardening
    • Assembly strength
    • Endurance strength
    • Work sample
• WM 6X00IN30 Working with adhesive tape and adhesive pads
  • Technical values
  • General information
    • Version
    • Shelf life
    • Disposal
    • Bonding log
  • Adhesive tape and adhesive pads on the bodywork
  • Working with adhesive tape and adhesive pads
    • General information
    • Preparing bonding surfaces
      • Initial cleaning
      • Cleaning
    • Processing conditions
    • Joining process
    • Assembly and endurance strength
• WM 6X00IN Gap dimensions
  • Technical values
  • Gap dimensions - 60 - Roof assembly