LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> 911 Turbo, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 113 (19 - Engine - Cooling -- CARRERA (997)) >> WM 195919 Removing And Installing Unit Carrier (Coolant Distributor Housing) (Except Turbo Coupe, Turbo S Coupe, Turbo CABRIO & Turbo S CABRIO) >> Preliminary Work

Preliminary Work

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Vehicle can fall down
  • Risk of squashing or crushing
  • Risk of damage to the vehicle

→ Do not place any solid objects under the raised vehicle.

→ Ensure that the lifting platform is prevented from lowering.

→ Remove solid objects before lowering the vehicle.

→ Raise the vehicle only at the jacking points provided.

→ The outer jacking points should be used primarily.

  1. Raise the vehicle.

    → 4X00IN01 LIFTING THE VEHICLE

  2. Place protective covers on the vehicle to avoid damaging the body and passenger compartment.
  3. Remove underbody panels at the rear and left.

    → 519419 REMOVING AND INSTALLING COVER FOR REAR UNDERBODY - section on "Removing"

    → 519319 REMOVING AND INSTALLING COVER FOR CENTRE UNDERBODY - section on "Removing"

  4. Remove air cleaner housing.

    → 242519 REMOVING AND INSTALLING AIR CLEANER HOUSING - section on "Removing"

  5. Remove resonance tube.

    → 247419 REMOVING AND INSTALLING RESONANCE TUBE - section on "Removing"

    Fig 1: Identifying Resonance Tube
    G09827803Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Slacken the drive belt -1-  .

    → 137819 REMOVING AND INSTALLING DRIVE BELT - section on "Removing"

    1. 6.1. Turn the tensioner -3-  clockwise at the hexagon (a/f 30) using a ring wrench -2-  and remove the belt -1-  .
    2. 6.2. Allow the tensioner to slide back to its initial position.
    Fig 2: Removing Drive Belt
    G09827804Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  7. Detach air conditioning compressor.

    → 873419 REMOVING AND INSTALLING AIR CONDITIONING COMPRESSOR - section on "Removing"

  8. Remove hydraulic pump.

    → 489819 REMOVING AND INSTALLING HYDRAULIC PUMP - section on "Removing"

  9. Remove the generator.
    1. 9.1. Loosen external Torx screws (E12, M8) -1, 2-  by two to three turns and fit screw insert (E12) with short extension on the screw head. Loosen threaded sleeves in the unit carrier by tapping gently with a plastic hammer.
    2. 9.2. Unscrew external Torx screw (E12, M8) -2-  and swivel the generator up.

      → 272219 REMOVING AND INSTALLING GENERATOR - section on "Removing"

    Fig 3: Removing Generator
    G09827805Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Drain coolant.

    → 193817 DRAINING AND FILLING COOLANT  - section on "Draining"

  11. Remove number plate and retainer plate.
  12. Remove front silencer.

    → 262519 REMOVING AND INSTALLING FRONT SILENCER - section on "Removing"

  13. Remove engine carrier.

    → 103019 REMOVING AND INSTALLING ENGINE CARRIER - section on "Removing"