LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2007 >> Solstice GXP, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Automatic Transmission - 5L40-E/5L50-E - Introduction (2 Of 2)) >> Repair Instructions >> Repair Instructions - On Vehicle >> Transmission Replacement >> Removal Procedure

Removal Procedure

WARNING: This page is about a different variant/trim than selected.
    IMPORTANT: NEW torque converter bolts will be required each time the torque converter bolts are removed.
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the starter motor to gain access to the torque converter bolts. Refer to Starter Motor Replacement .
    3. Fig 1: Left Side Transmission To Engine Mounting Bolts
    GM1615350Courtesy of GENERAL MOTORS CORP.
  3. Remove the left side transmission to engine mounting bolt (2).
    4. Fig 2: Upper Transmission Mounting Bolts
    GM1780573Courtesy of GENERAL MOTORS CORP.
  4. Remove the two upper transmission mounting bolts (1).
  5. If equipped, remove the turbocharger. Refer to Turbocharger Replacement .
    6. Fig 3: Right Side Transmission To Engine Mounting Bolts
    GM1615348Courtesy of GENERAL MOTORS CORP.
  6. Remove the right side transmission to engine mounting bolts (1, 2).
  7. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  8. Remove the front closeout panel. Refer to Floor Panel Tunnel Panel Front Closeout Panel Replacement .
  9. Drain the transmission fluid if disassembly of the transmission is necessary. Refer to Automatic Transmission Fluid and Filter Replacement .
    10. Fig 4: Shift Control Linkage
    GM1612916Courtesy of GENERAL MOTORS CORP.
  10. Remove the transmission manual shift shaft nut (1).
  11. Disconnect the shift linkage (2) from the transmission.
  12. Place the transmission in Neutral by rotating the transmission shift shaft clockwise 2 clicks.
  13. Remove the propeller shaft. Refer to Propeller Shaft Replacement .
    14. Fig 5: Wiring Harness Connector & Clips
    GM1780545Courtesy of GENERAL MOTORS CORP.
  14. Disconnect the transmission wiring harness connector (4) from the transmission by rotating the locking latch counterclockwise.
  15. Disconnect the wiring harness clips (1-3) from the transmission, and position the wiring harness aside.
    16. Fig 6: Flywheel Inspection Cover Bolt & Cover
    GM1780502Courtesy of GENERAL MOTORS CORP.
  16. Remove the flywheel inspection cover bolt (1) and cover (2).
  17. Mark the torque converter to flexplate/flywheel orientation to ensure proper realignment.
  18. Repeat the following steps for all 3 torque converter bolts:
    1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt with the starter motor opening in the engine block.
    2. Remove and discard the torque converter bolt. The bolt is self locking and is NOT reusable.
  19. Place an oil drain pan under the transmission fluid cooler pipes.
    20. Fig 7: Transmission Fluid Cooler Pipes Retainer
    GM1612921Courtesy of GENERAL MOTORS CORP.
  20. Remove the bolt (1) securing the transmission fluid cooler pipes retainer (2) to the transmission.
  21. Remove the transmission fluid cooler pipes from the transmission, and position aside.
  22. Remove the O-rings. Do not reuse the O-rings.
  23. Plug the open outlet ports to prevent fluid loss and contamination.
  24. Remove the catalytic converter. Refer to Catalytic Converter Replacement (LNF) or Catalytic Converter Replacement (LE5) .
  25. Position a suitable transmission jack under the transmission.
  26. Remove the transmission mount. Refer to Transmission Rear Mount Replacement .
    27. Fig 8: Left Side Transmission To Engine Mounting Bolts
    GM1615350Courtesy of GENERAL MOTORS CORP.
  27. Remove the left side transmission to engine mounting bolts (1).
    28. Fig 9: Right Side Transmission To Engine Mounting Bolts
    GM1615348Courtesy of GENERAL MOTORS CORP.
  28. Remove the right side transmission to engine mounting bolts (3).
  29. Pull the transmission free from the engine dowels.
  30. Carefully lower the transmission from the vehicle.
  31. Flush the transmission oil cooler. Refer to Automatic Transmission Oil Cooler Flushing and Flow Test (J 35944-A) or Automatic Transmission Oil Cooler Flushing and Flow Test (J 45096) .
  32. If the transmission is being replaced, remove the drive flange and install it on the replacement unit. Refer to Drive Flange and Seal Replacement .
scientia non olet · About LEMON Manuals