Display Item List
WARNING: This page is about a different car, the 2004 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
DISPLAY ITEM LIST
| CONSULT-II display | Item | Malfunction is detected when... | Reference |
|---|---|---|---|
| CAN COMM CIRC [U1000] | CAN communication | Malfunction is detected in CAN communication. | CAN COMMUNICATION INSPECTION USING CONSULT-II (SELF-DIAGNOSIS) |
| SEAT SLIDE [B2112] | Seat slide motor | When any manual and automatic operations are not performed, if any motor operations of seat slide is detected for 0.1 second or more, status is judged "Output error". | SLIDING MOTOR CIRCUIT INSPECTION SLIDING SENSOR CIRCUIT INSPECTION |
| SEAT RECLNING [B2113] | Seat reclining motor | When any manual and automatic operations are not performed, if any motor operations of seat reclining is detected for 0.1 second or more, status is judged "Output error". | FRONT LIFTER MOTOR CIRCUIT INSPECTION RECLINING SENSOR CIRCUIT INSPECTION |
| SEAT LIFTER-FR [B2114] | Seat lifting FR motor | When any manual and automatic operations are not performed, if any motor operations of seat lifting FR is detected for 0.1 second or more, status is judged "Output error". | FRONT LIFTER MOTOR CIRCUIT INSPECTION FRONT LIFTING SENSOR CIRCUIT INSPECTION |
| SEAT LIFTER-RR [B2115] | Seat lifting RR motor | When any manual and automatic operations are not performed, if any motor operations of seat lifting RR is detected for 0.1 second or more, status is judged "Output error". | REAR LIFTING MOTOR CIRCUIT INSPECTION REAR LIFTING SENSOR CIRCUIT INSPECTION |
| STEERING TILT [B2116] | Steering tilt motor | When any manual and automatic operations are not performed, if any motor operations of tilt is detected for 0.1 second or more, status is judged "Output error". | TELESCOPIC CIRCUIT INSPECTION |
| TELESCO MOTOR [B2117] | Steering telescopic motor | When any manual and automatic operations are not performed, if any motor operations of tilt is detected for 0.1 second or more, status is judged "Output error". | TELESCOPIC CIRCUIT INSPECTION |
| TILT SENSOR [B2118] | Steering tilt sensor | When steering tilt sensor detects 0.5V or lower, or 4.5V or higher, for 0.5 seconds or more. | TELESCOPIC SENSOR CIRCUIT INSPECTION |
| STEERING TELESCO SENSOR [B2119] | Steering telescopic sensor | When steering telescopic sensor detects 0.5V or lower, or 4.5V or higher, for 0.5 seconds or more. | TELESCOPIC SENSOR CIRCUIT INSPECTION |
| DETENT SW [B2126] | Detent SW | With the A/T selector lever in P position (Detent switch OFF), if the vehicle speed of 7 km/h (4 MPH) or higher was input the detent switch input system is judged malfunctioning. | A/T DEVICE (DETENT SWITCH) CIRCUIT INSPECTION (A/T MODEL ONLY) |
| PARKING BRAKE [B2127] | Parking brake | With parking brake use (Parking brake switch ON), if a vehicle speed of 7 km/h (4 MPH) or higher is input, the parking brake switch input system is judged malfunctioning. | PARKING BRAKE SWITCH CIRCUIT (M/T MODEL ONLY) |
| UART COMM [B2128] | UART communication | Malfunction is detected in UART communication. | UART COMMUNICATION LINE CIRCUIT INSPECTION |
NOTE:
- Parking brake malfunction will be detected when starting vehicle on grade or driving without releasing parking brake.
- The displays of CAN communication and detection switch display error detecting condition from memory erase to the present on "TIME".
- If error is detected in the past and present error is detected, "CRNT" is displayed.
- If error is detected in the past and present error is not detected, "PAST" is displayed.
- If error has never been detected, nothing is displayed on "TIME".
- Any items other than CAN communication and detection switch count error detection frequency occurred after erase history to "1 - 127".
- If error was detected in the past, error detection frequency from memory erase to the present is displayed on "TIME".
- If error has never been detected, nothing is displayed on "TIME".
- Can clear the detected memory.
- Normal: Clear memory in normal condition, history is erased and nothing is displayed on "TIME".
- Error: Clear memory in error condition, error is detected again and "1" is displayed on "TIME".