Replace the rear timing case cover

NOTE: RISK OF DAMAGE
Damage to the surface
The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage

Do not use any metal-cutting tools.

Remove the seal residue in areas (1) using special tool 0 495 102 (11 4 470) .

Courtesy of BMW OF NORTH AMERICA, INC.
Check the fitting sleeves (1) for damage and replace if necessary.
Check for correct fit of fitting sleeves (1) .

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
For additional information see: 11 00... OVERVIEW OF CONSUMABLES IN APPLICABLE BMW PARTS CATALOGUE

NOTE: TECHNICAL INFORMATION
The processing time of the liquid sealing compound can be at a maximum of 10 min.
Commissioning of the assembly is not possible until 25 minutes after the processing time.
Non-observance can lead to leaks in the assembly.

Courtesy of BMW OF NORTH AMERICA, INC.

Apply the sealing compound in area (1) along the inner edge.

SEALING COMPOUND SPECIFICATION

Loctite 5970 liquid sealing compound Processing time <10 minutes at room temperature

50 ml, Cartridge

83190404517

Mount the special tools 0 496 137 (11 8 815) and 0 496 132 (11 8 810) on the crankshaft

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the screws (1) to (11) and the timing case cover.
Parts: Screws, timing case cover
Carefully install the timing case cover.
Tighten screws in the sequence (1) to (11) .

TIGHTENING TORQUE SPECIFICATIONS

Rear timing case cover to engine block
M6 x 31 Replace screws.	Joining torque	8 Nm
M6 x 31 Replace screws.	Angle of rotation	90°

Fig 1: Timing Case Cover Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Connect connectors (1) and lock.
Make sure the connector (1) engages audibly.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to REFITTING OIL PAN .
Refer to INSTALLING FLYWHEEL (AUTOMATIC TRANSMISSION) .
Refer to SEALING THE OIL DUCT .
Refer to CLEANING SEALING SURFACES .
Refer to REPLACING CYLINDER HEAD GASKET .
Refer to INSTALLING THE CYLINDER HEAD (ENGINE REMOVED) .
Refer to ADJUSTING THE CAMSHAFTS WITH THE SPECIAL TOOL .
Refer to BLOCKING THE CRANKSHAFT IN HE TDC FIRING POSITION OF CYLINDER 1 .
Refer to INSTALLING EXHAUST CAMSHAFT ADJUSTER .
Refer to INSTALLING THE INTAKE ADJUSTER .
Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE INTAKE CAMSHAFT ADJUSTER .
Refer to PRE-TENSIONING THE TIMING CHAIN WITH THE SPECIAL TOOL .
Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to DISASSEMBLING ALL SPECIAL TOOLS .
Refer to INSTALLING CHAIN TENSIONER .
Refer to CHECKING THE TIMINGS OF THE CAMSHAFT .
Refer to INSTALLING THE INTAKE PLENUM .
Refer to INSTALLING THE TANK VENT VALVE .
Refer to INSTALLING EXHAUST TURBOCHARGER .
Refer to INSTALLING THE OIL FEED LINE FOR THE EXHAUST TURBOCHARGER .
Refer to INSTALLING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
Refer to INSTALLING THE CATALYTIC CONVERTER (ENGINE REMOVED) .
Refer to INSTALLING CYLINDER HEAD COVER .
Refer to INSTALLING BOTH ACTUATORS .
Refer to PREPARING FOR THE INSTALLATION OF THE HIGH PRESSURE PUMP .
Refer to INSTALLING HIGH PRESSURE PUMP .
Refer to INSTALLING INJECTORS .
Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE RAIL AND THE HIGH-PRESSURE PUMP .
Refer to INSTALLING FUEL DELIVERY LINE .
Refer to INSTALLING ALL SPARK PLUGS .
Refer to INSTALLING THE IGNITION COILS .
Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
Refer to INSTALLING LAMBDA OXYGEN SENSOR .
Refer to INSTALLING CLEAN AIR PIPE .
Refer to IF INSTALLED: PARTIALLY INSTALLING ENGINE VENTILATION LINE .
Refer to INSTALLING ACOUSTIC COVER .
Refer to REMOVING THE ENGINE FROM THE ASSEMBLY JIG .
Refer to FITTING THE MANUAL TRANSMISSION ON ENGINE .
Refer to INSTALLING THE AUTOMATIC TRANSMISSION ON THE ENGINE .
Refer to INSTALLING ENGINE .