Retrofit Rear Mercedes-Benz Dashcam With Existing Front Dashcam - AZ54.71-P-0003MFV

Model 247.6 

MODIFICATION NOTES

07.07.2020

Method description revised.

Operation step 7

Courtesy of MERCEDES-BENZ USA

Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Topical note	Notes on retrofitting electrical/optical lines		AH82.00-P-0000-01A
	Remove
1	Remove A-pillar trim on front passenger side.
			AR68.30-P-4050MFA
2	Remove front door sill on passenger side.
			AR68.30-P-4101MFA
3	Fold back passenger-side floor covering.
4	Remove upper B-pillar trim on front passenger side and place to one side with attached seat belt.
			AR68.30-P-4705MFA
5	Remove grab handles from roof on front passenger side.
			AR68.30-P-4330MFA
6	Remove trim from C-pillar on front passenger side and place to one side with seat belt attached.
			AR68.30-P-4490MFX
7	Remove trim from D-pillar on front passenger side and place to one side with seat belt attached.
			AR68.30-P-4497MFX
8	Remove overhead control panel control unit (N70).
			AR82.20-P-1000MFA
	Install
9	Retrofit mount of rear dashcam (2).	When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur.	AZ54.71-P-0003-00LWE
		Cleaner	*BR00.45-Z-1025-04A
	Remove
10	Remove cover of rain and light sensor with additional function (B38/2).
			AR82.30-P-7801MFA
11	Remove sun visor on front passenger side.
			AR68.60-P-5480MFA
12	Remove holder from driver's side sun visor.
			AR68.60-P-5480MFA
13	Detach front and rear edge guard on front passenger side in area of roof lining.
14	Release front and rear roof lining on front passenger side.
15	Remove upper liftgate trim.
			AR72.20-P-6631MFA
	Install
16	Retrofit wiring harness for dashcam.		AZ54.71-P-0003-01MFV
		Silicone spray Silicone-Fluid, 0.4 l art. no. 0893 221 000	*BR00.45-Z-1133-06A
		Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide	*BR00.45-Z-1144-02A
17	Latch dashcam at rear (2) into dashcam mount opposite direction of arrow on eject button.	Installation of the rear dashcam (2) should take place, at the earliest, an hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose.
18	Perform initial startup.		AZ54.71-P-0001-02LWE
	National settings for Mercedes-Benz dashcam		GF54.71-P-0010-02LWE
19	Install remaining parts.
	Update Vehicle Documentation (VeDoc)
20	Attach "Mercedes-Benz rear dashcam retrofitted as per AZ54.71-P-0003MFV" note under field organization texts to DG 54, DG 67 and DG 68.
	Check
21	Perform function test.	See Owner's Manual.

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71
BR00.45-Z-1133-06A	Silicone spray Silicone-Fluid, 0.4 l art. no. 0893 221 000	Adolf Wurth GmbH & Co. KG Reinhold-Wurth-Str. 12-17 74653 Kunzelsau-Gaisbach Germany Tel. +49 7940 15-0 Fax +49 7940 15-1000 http://www.wuerth.de
BR00.45-Z-1144-02A	Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide	A 008 989 50 85 09

PARTS ORDERING NOTE

Part no.	Designation	Quantity
KG 98 (see XPPI)	Dashcam parts kit	1