Update Software Of Reversing Camera (RFK) Control Unit (B84/3) (Code: VS2RU54KAM) - SM54.65-S-0029A

Model 447.6##/7## #3 as of 000527 up to 765268

with code FR8 (Rear view camera)

except code E2R (Radio generation 2)

OPERATION NO. OF OPERATION TEXTS OR STANDARD TEXTS AND FLAT RATES

Category	Op. no.	Operation text	Time	Acc. no.	Code
P	02 4762	Operations: Connect/disconnect vehicle diagnosis system (XENTRY Diagnosis)	-	54 923 11	VS2RU54KAM
P	02 5058	Operations: Connect/disconnect starter battery charger (XENTRY Diagnosis connected)	-	54 923 11	VS2RU54KAM
P	02 0022	Operations: Update reversing camera (RFK) control unit software (diagnostic system connected)	-	54 923 11	VS2RU54KAM

	Check
1	Check whether vehicle is affected by measure.	Affected vehicles: Update software of reversing camera (RFK) control unit (code: VS2RU54KAM) Model 447.6##/7## #3 as of 000527 up to 242724	SM54.65-S-0029-01AAA
		Affected vehicles: Update software of reversing camera (RFK) control unit (code: VS2RU54KAM) Model 447.6##/7## #3 as of 242726 up to 421089	SM54.65-S-0029-01BBB
		Affected vehicles: Update software of reversing camera (RFK) control unit (code: VS2RU54KAM) Model 447.6##/7## #3 as of 421094 up to 604796	SM54.65-S-0029-01CCC
		Affected vehicles: Update software of reversing camera (RFK) control unit (code: VS2RU54KAM) Model 447.6##/7## #3 from 604799 to 765268 For authorized Mercedes-Benz service partners, only the entry in the "Extended VEGA Application" (EVA) system, in the "Current" tab is decisive. An additional test of the affected vehicles in the workshop information system (WIS) or vehicle list is thereby not necessary.	SM54.65-S-0029-01DDD
	Installing
2	Install the 12 V charger.
		During the entire work procedure a sufficiently large voltage supply must be provided for the vehicle's on-board electrical system. Otherwise any undervoltage that occurs may damage the control units. Follow the operating instructions for the 12 V charger. Use the charger to ensure that an adequate power supply (min. 12.5 V) is provided for the on-board electrical system battery.	AR54.10-S-1127E
3	Install vehicle diagnosis system.	If XENTRY Diagnosis is not yet attached.
			AD00.00-S-2000-04E
	Service Information: Regio DVD and Retail Data Storage	Always make sure that XENTRY Diagnosis is updated to the latest version. For further information on "Retail Data Storage", see the service information above. It is essential to follow the operation steps in the diagnostic system. If XENTRY Diagnosis is already connected to vehicle, ↓ continue with operation step 4.	SI00.01-D-0044SG
	Update software
4	Update software for reversing camera (RFK) control unit (B84/3).
	Programming of control units	To do this, select the following menu items: Control units view → B84/3 - Reversing camera (code: FR8) → Adaptations → Control units update → Updating of control unit software You are then automatically guided through the steps "Updating of control unit software" and "SCN coding ". It is essential to follow the operation steps in the diagnostic system. After the control unit software is successfully updated, the following is shown: The procedure was completed successfully.	AR54.21-S-0014E
	Remove
5	Remove vehicle diagnosis system from vehicle.
6	Remove the 12 V charger from vehicle.
			AR54.10-S-1127E