Remove/Install Additional Battery - AR54.10-P-0007MEH
WARNING: This page does not describe the selected car, but rather 18 other vehicles, including the 2025 Mercedes-Benz Maybach GLS600, 2025 Mercedes-Benz GLS63 AMG, 2024 Mercedes-Benz Maybach GLS600, 2024 Mercedes-Benz GLS63 AMG, and 2023 Mercedes-Benz Maybach GLS600. However, it is still accessible from the selected car via links, so may be relevant.
Model 167 with engine 256
with code M016 (Uprated engine)
with code ME10 (Hybrid vehicle (plug-in, PHEV))
Model167
with code ME05 (Hybrid drive 85 kW-94 kW variant (incl. plug-in))
Shown on model 167.1
| Risk of fire
/risk of explosion due to short circuit and escaping oxyhydrogen gas. Risk of (burn) injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte/mist, short circuit and arcing Risk of poisoning caused by swallowing battery electrolyte or absorption of lead through the skin or body orifices. Risk of death due to voltage U >= 30 V AC and U >= 60 V DC. |
No fires, sparks, open flames, or smoking. Wear acid-resistant gloves, clothing, and glasses. Pour battery acid only into suitable and appropriately marked containers. | AS54.10-Z-0001-01A | |
| Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | AS00.00-Z-0011-01A | |
| Notice | Notes on battery | AH54.10-P-0001-01A | |
| Notice | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Notes on HANDS-FREE ACCESS | AH80.61-P-0001-01A | ||
| Remove/install | |||
| 1 | Remove rear shelf from vehicle. | Model 167.3 | |
| 2 | Lift load compartment floor until electrical connector of KEYLESS-GO antenna in front of load compartment is accessible. | ||
| 3 | Disconnect electrical connector of KEYLESS-GO antenna and remove load compartment floor from vehicle. | ||
| 4 | Remove right load compartment cover. | Model 167.1 | AR68.30-P-4800ME |
| Model 167.3 | AR68.30-P-1185MEC | ||
| 5 | Remove rear fuse and relay module with holder and place to one side with lines attached. | AR54.15-P-0001ME | |
| 6 | Unclip rear signal acquisition and actuation module from holder (1) and place to one side with lines attached | AR54.21-P-1273ME | |
| 7 | Remove bolt (2). | *BA68.30-P-1002-01G | |
| 8 | Remove screw (3) and remove mounting support (4). | ||
| 9 | Detach nuts (5) and remove holder (1). | ||
| 10 | Remove ground line (6) from ECO start/stop function auxiliary battery (G1/13). | ||
| Check | |||
| 11 | Use diode test lamp to check on-board electrical system for voltage between positive line (7) of ECO start/stop function auxiliary battery (G113) and a suitable ground point. | If the diode test lamp lights up, | |
| ↓ | |||
| Detach ground line from on-board electrical system battery and check the on-board electrical system after completing the work. | |||
| AR54.10-P-0003ME | |||
| 12 | Remove positive terminal cover. | ||
| 13 | Remove positive line (7) from ECO start/stop function auxiliary battery (G1/13). | Icon Cover up positive line (7) of ECO start/stop function auxiliary battery (G1/13). Otherwise, a short circuit may occur. |
|
| 14 | Unfasten nuts (8). | ||
| 15 | Unfasten holder (9). | ||
| 16 | Remove vent hose from auxiliary battery of ECO start/stop function (G1/13). | ||
| 17 | Remove auxiliary battery of ECO start/stop function (G1/13) upwards. | ||
| 18 | Install in the reverse order. |
PANELING, TRIM FRAME
| Number | Designation | Model 167 | ||
|---|---|---|---|---|
| BA68.30-P-1002-01G | Screw, load compartment floor mounting support to body | M8 | Nm | 32 |