Remove/Install Flywheel/Drive Plate - AR03.30-P-8001MRD

Engine 274.9 in model 213

Engine 274.9 in model 238

Fig 1: Flywheel/Drive Plate Components Location - Engine 274.9 In Model 213

Courtesy of MERCEDES-BENZ USA

	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	Notes on threaded connections fastened using a tightening angle-based tightening process		AH00.00-P-0020-01A
	Remove
1.1	Remove the transmission	Engine 274.9 in model 213 with transmission 725.0 Engine 274.9 in model 238 with transmission 725.0
		Engine 274.9 in model 213 (except 213.050) with transmission 725.0 except code M005 (4MATIC) Engine 274.9 in model 238 with transmission 725.0 except code M005 (4MATIC)	AR27.10-P-0500OLC
		Engine 274.9 in model 213 (except 213.050) with transmission 725.0 with code M005 (4MATIC) Engine 274.9 in model 238 with transmission 725.0 with code M005 (4MATIC)	AR27.10-P-0500OLD
		Engine 274.9 in model 213.050 with transmission 725.0 with code ME06 (Hybrid drive 60 kW variant (incl. plugin)) except code M005 (4MATIC)	AR27.10-P-0005MRD
1.2	Remove clutch	Engine 274.9 in model 213 with transmission 716.7 Engine 274.9 in model 238 with transmission 716.7
			AR25.10-P-0050OLC
2	Install retaining lock for crankshaft		AR03.30-P-5001MRD
3	Remove Screw/bolt/bolts (1a)	Do not use an impact wrench/driver or compressed air tool to remove screw/bolts (1) Otherwise the threads of the crankshaft will be damaged.
4	Remove flywheel/drive plate (1) from crankshaft flange
	Install
5	Check end cover (5) and radial shaft sealing ring (6) for damage	If damage is present ↓ Replace end cover (5) with radial shaft sealing ring (6).
			AR03.20-P-3064MRD
6	Position flywheel/drive plate (1) on crankshaft flange	The dowel pin for the crankshaft determines the installation position of the flywheel/drive plate (1).
7	Screw screw/bolts (1a) into crankshaft and tighten evenly cross-wise	Do not use an impact wrench/driver or compressed air tool to screw in the screw/bolts (1). Otherwise the threads of the crankshaft will be damaged.
		Bolt, two-mass flywheel/drive plate to crankshaft	*BA03.30-P-1003-01S
8	Remove retaining lock for crankshaft		AR03.30-P-5001MRD
9.1	Install transmission	Engine 274.9 in model 213 with transmission 725.0 Engine 274.9 in model 238 with transmission 725.0
		Engine 274.9 in model 213 (except 213.050) with transmission 725.0 except code M005 (4MATIC) Engine 274.9 in model 238 with transmission 725.0 except code M005 (4MATIC)	AR27.10-P-0500OLC
		Engine 274.9 in model 213 (except 213.050) with transmission 725.0 with code M005 (4MATIC) Engine 274.9 in model 238 with transmission 725.0 with code M005 (4MATIC)	AR27.10-P-0500OLD
		Engine 274.9 in model 213.050 with transmission 725.0 with code ME06 (Hybrid drive 60 kW variant (incl. plugin)) except code M005 (4MATIC)	AR27.10-P-0005MRD
9.2	Install clutch	Engine 274.9 in model 213 with transmission 716.7 Engine 274.9 in model 238 with transmission 716.7
			AR25.10-P-0050OLC

FLYWHEEL, DRIVE PLATE, VIBRATION DAMPER, STARTER RING GEAR

Number	Designation			Engine 274
BA03.30-P-1003-01S	Bolt, two-mass flywheel/drive plate to crankshaft	Stage 1	Nm	45
BA03.30-P-1003-01S	Bolt, two-mass flywheel/drive plate to crankshaft	Stage 2	∠°	90