Remove/Install Right Catalytic Converter - AR49.10-P-5503LF
Engine 157, 276.8, 278, 279 in model 217
Engine 157, 276.8/9, 277, 278, 279 in model 222
Shown on model 222 exhaust system with 276.8 engine with code 472 (gasoline particulate filter)
Shown on exhaust system for model 222 with engine 157
Shown on exhaust system with 278 engine from production date 2016-7-1
Shown on the exhaust system with engine 279
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Risk of burn injuries
, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust. |
Wear protective clothing and safety glasses. Use the extraction system. Move people out of the danger zone. |
AS49.00-Z-0001-01A | |
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. |
AS00.00-Z-0017-01A | |
| Notice | Notes on threaded connections fastened using a tightening angle-based tightening process | AH00.00-P-0020-01A | |
| Notice | Notes on avoiding damage through contamination and foreign objects | AH00.00-P-5000-01A | |
| Notice | Notes on self-locking nuts and bolts | AH00.00-P-0001-01KOA | |
| Remove | |||
| 1 | Remove rear center and middle lower engine compartment paneling | Engine 157, 276.8/9, 277, 278, 279 in model 222 with code Z07 (B7 armoring on special protection version) |
AR61.40-P-1001LFS |
| Engine 157, 276.8, 278, 279 in model 217 Engine 157, 276.8/9, 277, 278, 279 in model 222 except code Z07 (B7 armoring on special protection version) |
AR61.20-P-1105LF | ||
| 2 | Release electrical connection for left oxygen sensor upstream of left catalytic converter (2), disconnect and unclip electrical line | Engine 276.8 in model 217 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0081LFA |
| Engine 157 in model 222 Engine 157, 278 in model 217 Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0081LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0081MUB | ||
| 3 | Release electrical connection for left oxygen sensor upstream of left catalytic converter (2), disconnect and unclip electrical line | Engine 276.8 in model 217 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0082LFA |
| Engine 157 in model 222 Engine 157, 278 in model 217 Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0082LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0082MUB | ||
| 4 | Release electrical connection for right oxygen sensor upstream of right catalytic converter (3), disconnect and unclip electrical line | Engine 276.9 in model 222 | AR07.52-P-5303LFH |
| Engine 276.8 in model 217, 222 | AR07.04-P-0083LFA | ||
| Engine 157, 278 in model 217, 222 | AR07.04-P-0083LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0083MUB | ||
| 5 | Release electrical connection for right oxygen sensor downstream of right catalytic converter (3), disconnect and unclip electrical line | Engine 276.9 in model 222 | AR07.52-P-5303LFH |
| Engine 276.8 in model 217, 222 | AR07.04-P-0084LFA | ||
| Engine 157, 278 in model 217, 222 | AR07.04-P-0084LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0084MUB | ||
| 6.1 | Support left catalytic converter (2) and right catalytic converter (3) and secure against falling down | Engine 157, 276, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
| 6.2 | Support the right-hand catalytic converter (3) and secure it against falling down | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 7 | Remove the elastomer bearing (31) on the right-hand catalytic converter (3) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 8.1 | Unscrew the screws (14) of the left-hand catalytic converter (2) and the right-hand catalytic converter (3) | Engine 157, 276.8, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
| 8.2 | Unscrew the screws (14) of the right-hand catalytic converter (3) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 9.1 | Loosen the screw (15) of the left-hand catalytic converter (2) and screws (15) of the right-hand catalytic converter (3) | Engine 278 in model 217 as of 7/1/16 Engine 278 in model 222 as of 7/1/16 except code 472 (Gasoline particulate filter) |
|
| 9.2 | Loosen the screws (15) of the left-hand catalytic converter (2) and the screws on the right-hand catalytic converter (3) | Engine 157, 276.8, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 217 up to 6/30/16, 222 up to 6/30/16 |
|
| 9.3 | Loosen the screws (15) of the right-hand catalytic converter (3) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 10.1 | Unscrew the screws (10) of the left-hand catalytic converter (2) and the screws of the right-hand catalytic converter (3) | Engine 157 in model 222 Engine 157, 276.8, 278 in model 217 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
| 10.2 | Remove screws/bolts (16) and remove clamps (17) | Engine 277, 279 in model 222 Engine 279 in model 217 |
|
| 10.3 | Unscrew the screws (10) of the right-hand catalytic converter (3) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 11.1 | Loosen clamps (12, 13) and push back | Engine 157, 276.8, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
| 11.2 | Loosen the clamp (12) and push it back | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 12 | Unscrew the nuts (55) of the fastening plate, remove the fastening plate | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 13.1 | Remove the left-hand catalytic converter (2) and right-hand catalytic converter (3) from the bracket (22) towards the bottom | Engine 157, 276.8, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
| 13.2 | Remove the right-hand catalytic converter (3) from the bracket (22) towards the bottom | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 14 | Unfasten clamp (11) and push back | Engine 157, 277, 279 in model 222 Engine 157, 279 in model 217 When replacing the right catalytic converter (3). |
|
| 15 | Disconnect right CAT (2) from left CAT (3) | Engine 157, 277, 279 in model 222 Engine 157, 279 in model 217 When replacing the right catalytic converter (3). |
|
| 16 | Remove the gasket of the separation point at the clamp (12) after the right-hand catalytic converter (3) at the rear exhaust system | Engine 157, 276.8, 278, 279 in model 217 Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| Install | |||
| 17 | Check elastomer bearings of bracket (22) for damage | If damage is present ↓ Replace bracket (22). |
*BA49.10-P-1005-02D |
| *BA49.10-P-1005-01AN | |||
| 18 | Check the elastomer bearing (31) for damage | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) If damage is present ↓ Replace the elastomer bearing (31). |
|
| 19 | Remove combustion and corrosion residue at the connections | ||
| 20 | Replace the gasket of the separation point at the clamp (12) after the right-hand catalytic converter (3) at the rear exhaust system | Engine 157, 276.8, 278, 279 in model 217 Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 21 | Mount right CAT (2) on left CAT (3) | Engine 157, 277, 279 in model 222 Engine 157, 279 in model 217 When replacing the right catalytic converter (3). |
|
| 22.1 | Modify bracket (23) of right catalytic converter (3) | Engine 157, 277, 279 in model 222 Engine 157, 279 in model 217 Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) When replacing the right catalytic converter (3). |
|
| 22.2 | Convert the brackets (23, 24) of the left-hand catalytic converter (2) and right-hand catalytic converter (3) | Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 217 Engine 278 in model 222 except code 472 (Gasoline particulate filter) When replacing the right catalytic converter (3). |
|
| 23 | Position clamp (11) and tighten screw/bolt of the clamp (11) on the right CAT (3) slightly by hand | Engine 157, 277, 279 in model 222 Engine 157, 279 in model 217 When replacing the right catalytic converter (3). |
|
| 24.1 | Install and support the right-hand catalytic converter (3) and left-hand catalytic converter (2) on the bracket (22) | Engine 157, 276.8, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) Lubricant, rubber assembly 1 L |
*BR00.45-Z-1010-06A |
| 24.2 | Install and support the right-hand catalytic converter (3) to the bracket (22) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) Lubricant, rubber assembly 1 L |
*BR00.45-Z-1010-06A |
| 25 | Install the elastomer bearing (31) on the right-hand catalytic converter (3) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) Lubricant, rubber assembly 1 L |
*BR00.45-Z-1010-06A |
| 26 | Lightly tighten screw/bolts (14) by hand | ||
| 27 | Lightly tighten screw/bolts (15) by hand | ||
| 28.1 | Position clamps (12, 13) and tighten screw/bolts of clamps (12, 13) slightly by hand | Engine 157, 276.8, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
| 28.2 | Position the clamp (12) and slightly tighten the screws on the clamp (12) by hand | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 29.1 | Slightly tighten screw/bolts (10) by hand | Engine 157, 276.8, 278 in model 217 Engine157, 276.8/9, 278 in model 222 |
|
| 29.2 | Position clamps (17) and tighten screw/bolts (16) slightly by hand | Engine 277, 279 in model 222 Engine 279 in model 217 |
|
| 30 | Position the fastening plate and nuts (55) and slightly tighten by hand | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
|
| 31 | Check installation position and unobstructed movement of exhaust system, align if required | ||
| 32.1 | Tighten screw/bolts (10) | Engine 157, 276.8, 278 in model 217 Engine157, 276.8/9, 278 in model 222 |
*BA49.10-P-1001-01AN |
| *BA49.10-P-1001-02D | |||
| 32.2 | Fully tighten screw/bolts (16) | Engine 277, 279 in model 222 Engine 279 in model 217 Engine 279 in model 222 Clamp, front exhaust system to turbocharger |
*BA49.10-P-1023-01AN |
| *BA49.10-P-1013-02D | |||
| 33 | Fully tighten screw/bolts (14) | Engine 276 in model 217 Engine 278 in model 217 Bolt, front exhaust system bracket to transmission |
*BA49.10-P-1003-02D |
| *BA49.10-P-1012-02D | |||
Engine 276 in model 222 Engine 278 in model 222 Bolt, front exhaust system bracket to transmission |
*BA49.10-P-1003-01AN | ||
Engine 279 in model 222 Bolt, front exhaust system bracket to transmission and crankcase |
*BA49.10-P-1022-01AN | ||
| 34.1 | Tighten the screws (15) of the left-hand catalytic converter (2) and the screws of the right-hand catalytic converter (3) | Engine 157, 276.8, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 217 up to 6/30/16 Engine 278 in model 222 up to 6/30/16 except code 472 (Gasoline particulate filter) Engine 278 in model 217 up to 6/30/16 Bolt to front exhaust system bracket |
*BA49.10-P-1002-02D |
Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 up to 6/30/16 except code 472 (Gasoline particulate filter) Bolt to front exhaust system bracket |
*BA49.10-P-1002-01AN | ||
| 34.2 | Tighten the screws (15) of the right-hand catalytic converter (3) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) Bolt to front exhaust system bracket |
*BA49.10-P-1002-01AN |
| 34.3 | Tighten the screw (15) of the left-hand catalytic converter (2) and the screws (15) of the right-hand catalytic converter (3) | Engine 278 in model 217 as of 7/1/16 Engine 278 in model 222 as of 7/1/16 except code 472 (Gasoline particulate filter) |
*BA49.10-P-1002-02D |
except code 472 (Gasoline particulate filter) Bolt to front exhaust system bracket |
*BA49.10-P-1002-01AN | ||
| 35.1 | Tighten the clamp (12) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) Bolt, clamp for front/center/rear exhaust system |
*BA49.10-P-1006-01AN |
| 35.2 | Tighten the clamps (12, 13) | Engine 157, 276.8, 278, 279 in model 217 Engine 157, 277, 279 in model 222 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
|
Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) Engine 277 in model 222 Engine 278 in model 222 except code 472 (Gasoline particulate filter) Engine 279 in model 222 Bolt, clamp for front/center/rear exhaust system |
*BA49.10-P-1006-01AN | ||
Engine 276.8 in model 217 Engine 278 in model 217 Engine 279 in model 217 Bolt, clamp for front/center/rear exhaust system |
*BA49.10-P-1006-02D | ||
| 36 | Tighten the clamp (11) | Engine 157, 277, 279 in model 222 Engine 157, 279 in model 217 When replacing the right catalytic converter (3). |
*BA49.10-P-1006-01AN |
| *BA49.10-P-1006-02D | |||
| 37 | Tighten the nuts (55) | Engine 276.8 in model 222 with code 472 (Gasoline particulate filter) Engine 276.9 in model 222 Engine 278 in model 222 with code 472 (Gasoline particulate filter) |
*BA49.10-P-1025-01AN |
| 38 | Route electrical line of the left oxygen sensor upstream of left CAT (2); assemble and lock electrical connection | Engine 276.8 in model 217 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0081LFA |
| Engine 157 in model 222 Engine 157, 278 in model 217 Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0081LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0081MUB | ||
| 39 | Route electrical line of the left oxygen sensor upstream of left CAT (2); assemble and lock electrical connection | Engine 276.8 in model 217 Engine 276.8 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0082LFA |
| Engine 157 in model 222 Engine 157, 278 in model 217 Engine 278 in model 222 except code 472 (Gasoline particulate filter) |
AR07.04-P-0082LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0082MUB | ||
| 40 | Route electrical line of the right oxygen sensor upstream of right CAT (3); assemble and lock electrical connection | Engine 276.9 in model 222 | AR07.52-P-5303LFH |
| Engine 276.8 in model 217, 222 | AR07.04-P-0083LFA | ||
| Engine 157, 278 in model 217, 222 | AR07.04-P-0083LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0083MUB | ||
| 41 | Route electrical line of the right oxygen sensor upstream of right CAT (3); assemble and lock electrical connection | Engine 276.9 in model 222 | AR07.52-P-5303LFH |
| Engine 276.8 in model 217, 222 | AR07.04-P-0084LFA | ||
| Engine 157, 278 in model 217, 222 | AR07.04-P-0084LFB | ||
| Engine 277, 279 in model 222 Engine 279 in model 217 |
AR07.04-P-0084MUB | ||
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 42 | Perform an engine test run; check engine for functionality and exhaust system for leaktightness | ||
| 43 | Install lower rear and center engine compartment paneling | Engine 157, 276.8/9, 277, 278, 279 in model 222 with code Z07 (B7 armoring on special protection version) |
AR61.40-P-1001LFS |
| Engine 157, 276.8, 278, 279 in model 217 Engine 157, 276.8/9, 277, 278, 279 in model 222 except code Z07 (B7 armoring on special protection version) |
AR61.20-P-1105LF |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 222 | Engine 276 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1001-01AN | Bolt, front exhaust system to exhaust line | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 222 | |
|---|---|---|---|
| BA49.10-P-1001-01AN | Bolt, front exhaust system to exhaust line | Nm | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 217 | Engine 276 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1001-02D | Bolt, front exhaust system to exhaust line | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 217 | |
|---|---|---|---|
| BA49.10-P-1001-02D | Bolt, front exhaust system to exhaust line | Nm | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 222 | Engine 276 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1002-01AN | Bolt to front exhaust system bracket | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 277 in model 222 | Engine 278 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1002-01AN | Bolt to front exhaust system bracket | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 279 in model 222 | |
|---|---|---|---|
| BA49.10-P-1002-01AN | Bolt to front exhaust system bracket | Nm | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 217 | Engine 276 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1002-02D | Bolt to front exhaust system bracket | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 217 | Engine 279 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1002-02D | Bolt to front exhaust system bracket | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 222 | Engine 276 in model 222 | ||
|---|---|---|---|---|---|
| BA49.10-P-1003-01AN | Bolt, front exhaust system bracket to transmission | Stage 1 | Nm | 20 | 20 |
| Stage 2 | ∠° | - | - | ||
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 222 | ||
|---|---|---|---|---|
| BA49.10-P-1003-01AN | Bolt, front exhaust system bracket to transmission | Stage 1 | Nm | 20 |
| Stage 2 | ∠° | - | ||
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 217 | Engine 276 in model 217 | ||
|---|---|---|---|---|---|
| BA49.10-P-1003-02D | Bolt, front exhaust system bracket to transmission | Stage 1 | Nm | 20 | 20 |
| Stage 2 | ∠° | - | - | ||
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 217 | ||
|---|---|---|---|---|
| BA49.10-P-1003-02D | Bolt, front exhaust system bracket to transmission | Stage 1 | Nm | 20 |
| Stage 2 | ∠° | - | ||
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 222 | Engine 276 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1005-01AN | Bolt, bracket for elastomer bearing for front exhaust system to rear engine support | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 277 in model 222 | Engine 278 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1005-01AN | Bolt, bracket for elastomer bearing for front exhaust system to rear engine support | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 279 in model 222 | |
|---|---|---|---|
| BA49.10-P-1005-01AN | Bolt, bracket for elastomer bearing for front exhaust system to rear engine support | Nm | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 217 | Engine 276 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1005-02D | Screw/bolt, bracket for elastomer bearing for front exhaust system to rear engine support | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 217 | Engine 279 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1005-02D | Screw/bolt, bracket for elastomer bearing for front exhaust system to rear engine support | Nm | 20 | 20 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 222 | Engine 276 in model 222 | ||
|---|---|---|---|---|---|
| BA49.10-P-1006-01AN | Bolt, clamp for front/center/rear exhaust system | M8 | Nm | 35 | 35 |
EXHAUST SYSTEM
| Number | Designation | Engine 277 in model 222 | Engine 278 in model 222 | ||
|---|---|---|---|---|---|
| BA49.10-P-1006-01AN | Bolt, clamp for front/center/rear exhaust system | M8 | Nm | 35 | 35 |
EXHAUST SYSTEM
| Number | Designation | Engine 279 in model 222 | ||
|---|---|---|---|---|
| BA49.10-P-1006-01AN | Bolt, clamp for front/center/rear exhaust system | M8 | Nm | 35 |
EXHAUST SYSTEM
| Number | Designation | Engine 157 in model 217 | Engine 276 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1006-02D | Bolt, clamp for front/center/rear exhaust system | Nm | 35 | 35 |
EXHAUST SYSTEM
| Number | Designation | Engine 278 in model 217 | Engine 279 in model 217 | |
|---|---|---|---|---|
| BA49.10-P-1006-02D | Bolt, clamp for front/center/rear exhaust system | Nm | 35 | 35 |
EXHAUST SYSTEM
| Number | Designation | Engine 279 in model 217 | |
|---|---|---|---|
| BA49.10-P-1012-02D | Screw/bolt, front exhaust system bracket to transmission and crankcase | Nm | 38 |
EXHAUST SYSTEM
| Number | Designation | Engine 279 in model 217 | |
|---|---|---|---|
| BA49.10-P-1013-02D | Screw/bolt, front exhaust system clamp to turbocharger | Nm | 23 |
EXHAUST SYSTEM
| Number | Designation | Engine 277 in model 222 | Engine 279 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1022-01AN | Bolt, front exhaust system bracket to transmission and crankcase | Nm | 38 | 38 |
EXHAUST SYSTEM
| Number | Designation | Engine 277 in model 222 | Engine 279 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1023-01AN | Clamp, front exhaust system to turbocharger | Nm | 23 | 23 |
EXHAUST SYSTEM
| Number | Designation | Engine 276 in model 222 | Engine 278 in model 222 | |
|---|---|---|---|---|
| BA49.10-P-1025-01AN | Nut to mounting plate | Nm | 20 | 20 |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1010-06A | Lubricant, rubber assembly 1 L | A 000 989 03 67 |