Remove/Install Complete Rear Axle - AR35.10-P-0010MNE
Model 213.088/089/288/289
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Notes on handling, transport and storage of composite brake disks | AH42.10-P-9406-12LF | ||
| Notes on handling, transport and storage of ceramic brake disks | AH42.10-P-9406-13A | ||
| Notes on threaded connections fastened using a tightening angle-based tightening process | AH00.00-P-0020-01A | ||
| Notes on self-locking nuts and bolts | AH00.00-N-0001-01A | ||
| Notes on repair work on suspension components | AH00.00-P-0100-01A | ||
| Notes on AIRmatic | Model 213.088/089/288/289 with code 489 (AIRMATIC) | AH32.22-P-1000-02LW | |
| Remove/install | |||
| 1 | Shift transmission to N position. | ||
| 2 | Secure vehicle on vehicle lift. | AR00.60-P-0100CW | |
| 3 | Vent pressure in AIRMATIC system using vehicle diagnosis system. | ||
| AD00.00-P-2000-04B | |||
| 4 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m). | ||
| 5 | Remove brake caliper with connected brake hoses and hang to one side free of tension. | AR42.10-P-0080LW | |
| 6 | Remove propeller shaft (1) from rear axle differential, hook up to one side and fix in place. | AR41.10-P-0050LW | |
| 7 | Remove rear shock absorbers. | AR32.25-P-0110LW | |
| 8 | Remove screws (13, 14) and hook up bracket (12) with electric lines (15) to one side. | ||
| 9 | Unscrew bolts (10). | *BA42.30-P-1001-02K | |
| 10 | Remove brackets (2) with rear axle RPM sensors (L6/3, L6/4) and electric lines (4, 15), hook up to one side and fix in place. | ||
| 11 | Remove air suspension bellows. | Model 213.088/089/288/289 with code 489 (AIRMATIC) | AR32.22-P-1500MNE |
| 12 | Unclip electric lines from holders of rear level sensors (B22/7, B22/10). | ||
| 13 | Disconnect electrical connectors (20) from rear level sensors (B22/7, B22/10) and hook up electric lines to one side. | ||
| 14 | Separate electrical connection (16). | ||
| 15 | Unclip electric line (17) from rear axle differential. | ||
| 16 | Unclip electric lines (18) from rear axle carrier. | ||
| 17 | Remove screws (5) from stop plates (6). | *BA35.10-P-1003-01H | |
| 18 | Position lifting platform with mount on rear axle (7) and secure with tensioning strap. | ||
| 000 588 03 62 00 Lifting platform | WS01.00-P-0091A | ||
| 19 | Unscrew screws (8) and remove stop plates (6). | Otherwise, the threads will be damaged. |
|
| *BA35.10-P-1001-01H | |||
| 20 | Unscrew screws/bolts (9). | Otherwise, the threads will be damaged. |
|
| *BA35.10-P-1002-01H | |||
| 21 | Lower rear axle (7) until the electrical connector of the electronic locking differential is accessible. | ||
| 22 | Disconnect electrical connector of automatic locking differential. | ||
| 23 | Lower rear axle (7). | If not, ↓ perform cavity preservation. |
AR35.10-P-0010-03A |
| 000 588 01 72 00 Sealing and corrosion protection gun | WS97.00-N-0002B | ||
| Cavity preservation (free of solvents), 1 liter | *BR00.45-Z-1003-05A | ||
| 24 | Install in the reverse order | ||
| Measure | |||
| 25 | Perform chassis alignment. | AR40.20-P-0200LW |
REAR AXLE CARRIER
| Number | Designation | Model 213 | ||
|---|---|---|---|---|
| BA35.10-P-1001-01H | Self-locking bolt securing front decoupling element of rear axle carrier to frame floor assembly | Stage 1 | Nm | 100 |
| Stage 2: Loosen | ∠° | 180 | ||
| Stage 3 | Nm | 100 | ||
| Stage 4 | ∠° | 90 | ||
REAR AXLE CARRIER
| Number | Designation | Model 213 | ||
|---|---|---|---|---|
| BA35.10-P-1002-01H | Self-locking bolt securing rear decoupling element of rear axle carrier to frame floor assembly | Stage 1 | Nm | 100 |
| Stage 2: Loosen | ∠° | 180 | ||
| Stage 3 | Nm | 100 | ||
| Stage 4 | ∠° | 90 | ||
REAR AXLE CARRIER
| Number | Designation | Model 213 | |
|---|---|---|---|
| BA35.10-P-1003-01H | Bolt, stop plate to body | Nm | 35 |
REAR AXLE RPM SENSOR
| Number | Designation | Model 213 | |
|---|---|---|---|
| BA42.30-P-1001-02K | Bolt, RPM sensor to wheel carrier | Nm | 8 |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1003-05A | Cavity preservation (free of solvents), 1 liter | A 000 986 72 70 10 |