Remove/install rear axle shaft flange and angular ball bearing - AR35.20-P-0130SX
MODEL 216 (except 216.379)
MODEL 221 (except 221.179)
MODEL 221
MODIFICATION NOTES
| 20.1.10 | Special tool 140 589 01 34 00 replaced by special tool 211 589 02 34 00 | AR35.20-P-0130-02TX |
| Removing | |||
| Notes on self-locking nuts and bolts | AH00.00-N-0001-01A | ||
| While working on the rear axle care must be taken to ensure that the surface of all aluminum components do not get any scratches, cracks and notches. Otherwise the service life of the parts will be affected | |||
| 1 | Remove wheel. | ||
| Remove/install wheels | AP40.10-P-4050SX | ||
| 2 | Detach twelve-point collar nut (1) from rear axle shaft (2) | AR35.30-P-0115-01SX | |
| *BA35.30-P-1001-01I | |||
| *220589010900 | |||
| 3 | Move electronic parking brake into assembly position using STAR DIAGNOSIS | ||
| 4 | Remove brake disk (3) | AR42.10-P-0220SX | |
| 5 | Remove brake shoes (8) | AR42.20-P-0530SX | |
| 6 | Pull rear axle shaft flange (4) out of angular contact ball bearing (5) | AR35.20-P-0130-06SX | |
| *202589044310 | |||
| *211589013300 | |||
| 7 | Detach angular contact ball bearing (5) from wheel carrier (7) | ||
| 8 | Clean water drain in wheel carrier (7) | AR35.20-P-0115-03CW | |
| 9 | Pull bearing inner race off the rear axle shaft flange (4) | AR35.20-P-0130-02TX | |
| *001589503300 | |||
| *211589023400 | |||
| *124589023400 | |||
| Install | |||
| 10 | Mount angular contact ball bearing (5) on wheel carrier (7) | *BA35.20-P-1001-06A | |
| 11 | Pull rear axle shaft flange (4) into angular contact ball bearing (5) | AR35.20-P-0130-07SX | |
| *210589034300 | |||
| *211589003300 | |||
| 12 | Install brake shoes (8) | AR42.20-P-0530SX | |
| 13 | Install brake disk (3) | AR42.10-P-0220SX | |
| 14 | Mount and secure twelve-point collar nut (1) on rear axle shaft (2) | AR35.30-P-0115-01SX | |
| *BA35.30-P-1001-01I | |||
| *220589010900 | |||
| 15 | Detach wheel | ||
| Remove/install wheels | AP40.10-P-4050SX |
HUB
| Number | Designation | Model 216 | Model 221 | |
|---|---|---|---|---|
| BA35.20-P-1001-06A | Wheel bearing to wheel carrier | Nm | 70 | 70 |
REAR AXLE SHAFT
| Number | Designation | Model 216 except model 216.379 | Model 221 without code Z07/Z07+Z19 except model 221.179 | ||||
|---|---|---|---|---|---|---|---|
| BA35.30-P-1001-01I | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | M26 | Nm | 350 | 350 | |
| not self-locking | M26 | Stage 1 | Nm | 170 | 170 | ||
| Stage 2 | ∠° | 45 | 45 | ||||
| not self-locking | M29 | Stage 1 | Nm | - | - | ||
| Stage 2 | ∠° | - | - |