Propeller Shaft -- Cl550 -- 216 Chassis

• Testing & Repair
  • Testing and repair work: Passenger cars: Propeller shaft - AR41.00-Z-9216AA
  • Detach front propeller shaft from transmission - AR41.10-P-0050-02SX
  • Remove propeller shaft from rear axle center assembly. - AR41.10-P-0050-03SX
  • Mount rear propeller shaft to rear axle center assembly - AR41.10-P-0050-04SX
  • Connect sections of propeller shaft - AR41.10-P-0050-05SX
  • Mount front propeller shaft to transmission - AR41.10-P-0050-07SX
  • Release fitting sleeves on flex disks - AR41.10-P-0050-09SX
  • Loosen bolts of propeller shaft intermediate bearing - AR41.10-P-0050-10SX
  • Mount propeller shaft intermediate bearing - AR41.10-P-0050-11SX
  • Remove/install propeller shaft - AR41.10-P-0050SX
  • Remove/install propeller shaft - AR41.10-P-0050SYZ
  • Remove/install front axle transmission propeller shaft - AR41.10-P-0070SYZ
  • Measure absolute angle at transmission - AR41.10-P-0085-01SX
  • Measure absolute angle at front and rear propeller shafts - AR41.10-P-0085-02SX
  • Measure absolute angle at rear axle housing - AR41.10-P-0085-03T
  • Read out propeller shaft inclination angles from memory; correct if necessary - AR41.10-P-0086-01R
  • Prepare electronic propeller shaft inclinometer - AR41.10-P-0086-02P
  • Correcting front inclination angle at transmission - AR41.10-P-0086-03T
  • Correcting center articulation angle at propeller shaft intermediate bearing - AR41.10-P-0086-04T
  • Correcting rear articulation angle at rear axle center assembly - AR41.10-P-0086-05SX
  • Measure propeller shaft alignment with electronic propeller shaft inclinometer - AR41.10-P-0086SX
  • Pressing grooved ball bearing out of rubber mount of propeller shaft, pressing in - AR41.10-P-0100-02SX
  • Press rubber mount with grooved ball bearing onto linkage arm - AR41.10-P-0100-05SX
  • Pull off rubber mount with grooved ball bearing - AR41.10-P-0100-07SX
  • Remove/install propeller shaft intermediate bearing and replace grooved ball bearing - AR41.10-P-0100SX
  • Removal of centering sleeve - AR41.10-P-0200-02SX
  • Press in guide sleeve - AR41.10-P-0200-03SX
  • Replace centering sleeve - AR41.10-P-0200SX
• Test & Adjustment Values
  • Test and adjustment values: Passenger cars: Propeller shaft - BE41.00-Z-9999AZ
  • Capacities: Passenger cars: Propeller shaft - BF41.00-Z-9999AZ
  • Propeller shaft - BE41.10-P-1000-01F
• Maintenance
  • Check propeller shaft flex disks for signs of damage and deformation - AP41.10-P-4152SX
• Torque Specifications
  • Tightening torques: Passenger cars: Propeller shaft - BA41.00-Z-9999AZ
  • Propeller shaft - BA41.10-P-1000-01H
  • Propeller shaft intermediate bearing - BA41.40-P-1000-01E
• Forms
  • Data Sheet for Measuring Inclination Angle, Form - OF41.10-P-3000-01A
• Special Tools
  • 116 589 09 43 00 Removal and installation tool - WS41.00-P-0001C
  • 126 589 03 15 00 Drift - WS41.00-P-0003C
  • Special tools: Passenger cars: Propeller shaft - WS41.00-Z-9999AZ