Remove/install wheel carrier - AR35.20-P-0115B

Model 129, 170, 202, 208, 210 

Fig 1: Identifying Wheel Carrier - Version Up To 12/97 Or 01/98

Version up to 12/97 or 01/98 

Fig 2: Identifying Wheel Carrier - Version As Of 01/98 Or 02/98

Version as of 01/98 or 02/98 

	28.2.98	Diameter of wheel carrier bores modified	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0005-01A
	28.2.98	Bolted connection, camber strut to wheel carrier modified	Tightening torque of bolted connection M10 increased from 45 Nm to 70 Nm  for new bolted connection M12.	BT35.20-P-0007-01A
	28.2.98	Bolted connection, tension arm to wheel carrier modified	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0008-01A
	28.2.98	Bolted connection, torque strut to wheel carrier modified	Tightening torque of bolted connection M10 increased from 45 Nm to 70 Nm  for new bolted connection M12.	BT35.20-P-0006-01A
	28.2.98	If a new camber strut, rebound strut or thrust arm is mounted to an existing wheel carrier version (ø of fastening bore in wheel carrier approx. 13.5 mm), the sleeve (2h, 3h, 5h) must be mounted to the wheel carrier, to achieve a ø reduction of approx. 12.2 mm	Model 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see: ↓
			Install sleeve for camber strut in wheel carrier	AR35.20-P-0110-02A
			Install sleeve for torque strut in wheel carrier	AR35.20-P-0111-01A
			Install sleeve for thrust arm in wheel carrier	AR35.20-P-0113-01A

Fig. item, etc.	Work instructions
Installation	Replace self-locking nuts and bolts
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
Installation	Install camber strut, tension arm, torque strut, track rod and spring link at wheel carrier	The rear axle shaft must be horizontal when tightening the nuts
Installation	Check toe at rear axle and adjust if necessary		AR40.20-P-0332A
	Removing and installing brake shoes of parking brake		AR42.20-P-0530A
2	Camber strut
	Bolted connection, camber strut to wheel carrier modified	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0007-01A
			*BA35.20-P-1002-02A
2 h	Sleeve in wheel carrier to reduce diameter	Models 129, 170, 202, 208 as of 02/98
		Model 210 as of 01/98, see:↓ Install sleeve for camber strut in wheel carrier	AR35.20-P-0110-02A
3	Torque strut	Box wrench	Figure
		Retainer wrench for counterholding torx socket bolt	Figure
			*BA35.20-P-1002-03A
	Bolted connection, tension arm to wheel carrier modified	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0008-01A
3 h	Sleeve in wheel carrier to reduce diameter	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see: ↓
		Install sleeve for torque strut in wheel carrier	AR35.20-P-0111-01A
4	Remove/install track rod		AR35.20-P-0112B
5	Thrust arm
	Bolted connection, torque strut to wheel carrier modified	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0006-01A
			*BA35.20-P-1002-05A
5 h	Sleeve in wheel carrier to reduce diameter	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see: ↓
		Install sleeve for thrust arm in wheel carrier	AR35.20-P-0113-01A
6	Spring control arm		*BA35.20-P-1002-01A
7	Wheel carrier	Remove front rear axle shaft.
	Diameter of wheel carrier bores modified	Models 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0005-01A
12	Remove/install and secure rear axle shaft twelve-point collar nut		AR35.30-P-0115-01A
			*BA35.30-P-1001-01A
37	Rear axle shaft	Pull out of rear axle shaft flange. If the rear axle shaft is difficult to remove: ↓ Push rear axle shaft out of rear axle shaft flange, pull in: ↓ Models 129, 202, 210 up to 31.01.96	AR35.30-P-0115-03A
		Removal and installation tool	Fig 3
		Extraction and insertion tool	Fig 4
		Models 129, 202, 210 as of 01.02.96 and Models 170, 208	AR35.30-P-0115-03B
		Extraction and insertion tool	Fig 4
		Bracket	Fig 5
	Rear axle shafts with forged centers (without core hole)	As of 02/96	BT35.30-P-0005-01A
112 A	Remove/install rear brake control cable		AR42.20-P-0525A
112 C	Brake cover
L6/3, L6/4	Remove/install left or right rear axle speed sensor	Vehicles with ASR, ETS, ESP as of 06/94	AR42.40-P-0820A

Spring link

Spring link

Camber strut

Camber strut

Torque strut

Torque strut

Torque strut

Rear axle shaft

Rear axle shaft

Fig 3: Identifying Removal And Installation Tool (140 589 03 61 00)

Fig 4: Identifying Extraction And Insertion Tool (210 589 03 43 00)

Fig 5: Identifying Bracket (210 589 01 40 00)

Fig 6: Identifying Ring wrench (129 589 01 03 00)

Fig 7: Identifying Retainer Wrench (202 589 00 10 00)