Remove/install pop-up bracket on tilting/sliding roof - AR77.20-P-1700A

MODEL 463.220 /221 /222 /224 /225 /227 /228 /230 /231 /232 /233 /236 /237 /240 /241 /243 /244 /245 /246 /247 /248 /249 /270 /271 /320 /321 /322 /323 /324 /325 /327 /328 /330 /331 /332 /333 /336 /340 /341 /346 with CODE (D27) Power tilting/sliding roof 

Fig 1: Identifying Guide Plate, Sliding Carrier And Control Cable Guide Tube

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying Tilting/Sliding Roof Panel Mounting Bracket

Courtesy of MERCEDES-BENZ USA

Fig 3: Removing Tilting Bracket

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Slide Shoe

Courtesy of MERCEDES-BENZ USA

Fig 5: Identifying Setting Gauge

Courtesy of MERCEDES-BENZ USA

Fig 6: Identifying Marking & Marking Notch

Courtesy of MERCEDES-BENZ USA

	Removing
1	Remove paneling from tilting/sliding roof		AR77.20-P-0500G
2	Remove tilting/sliding roof panel		AR77.20-P-1000A
3	Remove guide plate (1) from sliding carrier (2)
4	Remove mounting bracket from tilting/sliding roof panel (4)	Remove upward out of side guide (gate).
5	Remove water drain runnel		AR77.20-P-1999A
6	Remove sliding carrier (2)
7	Remove tilting bracket (5)	Slide tilting bracket (5) to stop toward front, tilt upward and remove toward inside at an angle.
	Install
8	Grease tilting bracket (5) on sliding jaws (7) and moving parts with lubricant		*BR00.45-Z-1004-06A
9	Install tilting bracket (5)	Ensure that sliding jaws (7) are seated properly, otherwise malfunctions can occur.
10	Install sliding carrier (2)	Press tilting bracket (5) slightly outwards with screwdriver, then tighten bolts on sliding carrier (2).
11	Install water drain runnel		AR77.20-P-1999A
12	Adjust basic position on tilting bracket mechanism	Insert left and right adjustment gauges (6) into side guide (gate) and into groove in tilting bracket (5) (arrows). Do not remove adjustment gauges (6) until tilting/sliding roof panel is installed.
			Fig 7
			Fig 8
13	Install mounting bracket for tilting/sliding roof panel (4)
14	Screw guide plate (1) to sliding carrier (2)
15	Instal tilting/sliding roof panel		AR77.20-P-1000A
16	Remove left and right adjustment gauges (6)		Fig 7
			Fig 8
17	Actuate tilting/sliding roof and move to all positions a number of times
18	Close tilting/sliding roof and check markings (8) and marking notches (9) at left and right sliding rail	If the marking (8) is outside the marking notches (9) on the slide rail, see: ↓ Remove paneling from rear pillar. Only on left side.	MODEL 463.220 /221 /224 /225 /227 /228 /230 /231 /232 /233 /240 /241 /320 /321 /324 /325 /327 /328 /330 /331
		Model 463.222 /237 /243 /244 /245 /246 /247 /249 /270 /271 /322 /323 /332 /333 /336 /340 /341 /346 Model 463.236 / 248	AR68.30-P-4505GK
		Carry out fine adjustment of tilting/sliding roof	AR77.20-P-1100-02A
19	Carry out function check
20	Install paneling on tilting/sliding roof		AR77.20-P-0500G
21	Install paneling on rear pillar	Only if paneling was removed. MODEL 463.220 /221 /224 /225 /227 /228 /230 /231 /232 /233 /240 /241 /320 /321 /324 /325 /327 /328 /330 /331
		Model 463.222 /237 /243 /244 /245 /246 /247 /249 /270 /271 /322 /323 /332 /333 /336 /340 /341 /346 Model 463.236 / 248	AR68.30-P-4505GK

Fig 7: Identifying Adjustment Gauge (124 589 17 21 00)

Courtesy of MERCEDES-BENZ USA

Fig 8: Identifying Adjustment Gauge (124 589 18 21 00)

Courtesy of MERCEDES-BENZ USA