Remove/install passenger compartment floor covering - AR68.20-P-2045GR

MODEL 463.202 /222 /236 /237 /243 /244 /245 /246 /247 /248 /249 /250 /254 /270 /271 /303 /306 /309 /322 /323 /332 /333 /336/340 /341 /346 

Shown on left 

Fig 1: Identifying Door Sill Moldings, Front Tunnel Paneling And Accelerator Pedal

Courtesy of MERCEDES-BENZ USA

Shown on left 

Fig 2: Identifying Front Door Sill Molding, Floor Covering And Electrical Connector

Courtesy of MERCEDES-BENZ USA

	Remove/install
1.1	Remove seat and console	Model 463.236/237/243/245/246/248/249/270/271/323/333/341/346	AR91.10-P-3300GR
1.2	Remove front seat	Model 463.202/222/244/247/250/254/303/306/309/322/332/336/340 with wheelbase 2400 mm	AR91.10-P-1000GM
2	Remove TELE AID control unit (A35/8)	Only on model 463.246/249/271 with code (ET2) TELE AID car telephone emergency call system When removing floor covering on passenger side.	AR82.95-P-0014US
3	Remove front door sill (1) and rear door sill (2)	Front door sill (1) and rear door sill (2) are only inserted. Pry out with assembly wedge at several points.
			Figure
4	Unplug electrical connector (3) for front door sill molding (1)
5	Remove front tunnel paneling (4)	Remove three bolts.
6	Remove accelerator pedal (5)	Only if front floor covering (6) is to be removed.
		Model 463.244/245/250 with engine 112.945 Model 463.247/248/249/254 with engine 113.962 Model 463.243/246 with engine 113.982 Model 463.322/323 with engine 612.965 Model 463.309/332/333 with engine 628.962 Model 463.270/271 with engine 113.993	AR30.12-P-1321GR
		Model 463.303/340/341 with engine 642, Model 463.202/222/236/237 with engine 273 Model 463.306/336/346	AR30.12-P-1321GY
7	Remove center console	Model 463.202/222/236/243/244/245/247/248/250/254/270/303/306/309/322/323/332/333/336/340/341/346	AR68.20-P-2000GA
		Model 463.237/246/249/271	AR68.20-P-2000US
8.1	Remove paneling on B-pillar	Model 463.243/245/246/248/249/323/333 up to 31.5.04 with wheelbase of 2850 mm	AR68.30-P-4700GN
		Model 463.243/245/246/248/249/323/333 as of 1.6.04, Model 463.236/237/270/271/341/346	AR68.30-P-4700GY
8.2	Remove bottom side wall paneling (9)	Model 463.222/244/ 247/322/332/336/340 For this purpose, remove belt end fitting and unclip lower side wall paneling (9). Installation:  Ensure that clips are complete.
			Figure
			*BA91.40-P-1001-01C
8.3	Remove bottom side wall paneling (9)	Model 463.202/250/254/303/306/309 with hydraulic soft top	AR68.30-P-1450GA
9	Remove front floor covering (6)
10	Remove tunnel floor covering (7)
11	Remove center floor covering (8)	When removing, the left side of the center floor covering (8) is fastened to the parking brake bearing bracket with two threaded pins.
12	Install in the reverse order

Fig 3: Identifying Mounting Wedge (110 589 03 59 00)

Courtesy of MERCEDES-BENZ USA