Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B155E:00 | Incorrect Response from Immobilizer SubControl Module: No Sub Type Information | GO to Pinpoint Test J |
| BCM | B155F:51 | Phone As A Key: Not Programmed | GO to Pinpoint Test F |
| PCM | P1594:00 | Forced Engine Shutdown: Remote Start Fault, No Unattended Vehicle Timeout | GO to Pinpoint Test L |
| PCM | P1595:00 | Forced Engine Shutdown: Remote Start System Fault, Transmission Range Not In Park Position | GO to Pinpoint Test L |
| RFA | B1589:29 | Antenna #3: Signal Invalid | GO to Pinpoint Test A |
| RFA | B1589:31 | Antenna #3: No Signal | GO to Pinpoint Test A |
| RFA | B1589:45 | Antenna #3: Program Memory Failure | GO to Pinpoint Test A |
| RFA | B1589:49 | Antenna #3: Internal Electronic Failure | GO to Pinpoint Test A |
| RFA | B1589:57 | Antenna #3: Invalid/ Incompatible Software Component | GO to Pinpoint Test A |
| RFA | B1590:29 | Antenna #4: Signal Invalid | GO to Pinpoint Test A |
| RFA | B1590:31 | Antenna #4: No Signal | GO to Pinpoint Test A |
| RFA | B1590:45 | Antenna #4: Program Memory Failure | GO to Pinpoint Test A |
| RFA | B1590:49 | Antenna #4: Internal Electronic Failure | GO to Pinpoint Test A |
| RFA | B1590:57 | Antenna #4: Invalid/ Incompatible Software Component | GO to Pinpoint Test A |
| RFA | B1591:29 | Antenna #5: Signal Invalid | GO to Pinpoint Test B |
| RFA | B1591:31 | Antenna #5: No Signal | GO to Pinpoint Test B |
| RFA | B1591:45 | Antenna #5: Program Memory Failure | GO to Pinpoint Test B |
| RFA | B1591:49 | Antenna #5: Internal Electronic Failure | GO to Pinpoint Test B |
| RFA | B1591:57 | Antenna #5: Invalid/ Incompatible Software Component | GO to Pinpoint Test B |
| RFA | B1592:29 | Antenna #6: Signal Invalid | GO to Pinpoint Test B |
| RFA | B1592:31 | Antenna #6: No Signal | GO to Pinpoint Test B |
| RFA | B1592:45 | Antenna #6: Program Memory Failure | GO to Pinpoint Test B |
| RFA | B1592:49 | Antenna #6: Internal Electronic Failure | GO to Pinpoint Test B |
| RFA | B1592:57 | Antenna #6: Invalid/ Incompatible Software Component | GO to Pinpoint Test B |
| RFA | B1593:29 | Antenna #7: Signal Invalid | GO to Pinpoint Test B |
| RFA | B1593:31 | Antenna #7: No Signal | GO to Pinpoint Test B |
| RFA | B1593:45 | Antenna #7: Program Memory Failure | GO to Pinpoint Test B |
| RFA | B1593:49 | Antenna #7: Internal Electronic Failure | GO to Pinpoint Test B |
| RFA | B1593:57 | Antenna #7: Invalid/ Incompatible Software Component | GO to Pinpoint Test B |
| RFA | B1594:29 | Antenna #8: Signal Invalid | GO to Pinpoint Test C |
| RFA | B1594:31 | Antenna #8: No Signal | GO to Pinpoint Test C |
| RFA | B1594:45 | Antenna #8: Program Memory Failure | GO to Pinpoint Test C |
| RFA | B1594:49 | Antenna #8: Internal Electronic Failure | GO to Pinpoint Test C |
| RFA | B1594:57 | Antenna #8: Invalid/ Incompatible Software Component | GO to Pinpoint Test C |
| RFA | B1596:29 | Antenna #10: Signal Invalid | GO to Pinpoint Test B |
| RFA | B1596:31 | Antenna #10: No Signal | GO to Pinpoint Test B |
| RFA | B1596:45 | Antenna #10: Program Memory Failure | GO to Pinpoint Test B |
| RFA | B1596:49 | Antenna #10: Internal Electronic Failure | GO to Pinpoint Test B |
| RFA | B1596:57 | Antenna #10: Invalid/ Incompatible Software Component | GO to Pinpoint Test B |
| RFA | B1597:29 | Antenna #11: Signal Invalid | GO to Pinpoint Test C |
| RFA | B1597:31 | Antenna #11: No Signal | GO to Pinpoint Test C |
| RFA | B1597:45 | Antenna #11: Program Memory Failure | GO to Pinpoint Test C |
| RFA | B1597:49 | Antenna #11: Internal Electronic Failure | GO to Pinpoint Test C |
| RFA | B1597:57 | Antenna #11: Invalid/ Incompatible Software Component | GO to Pinpoint Test C |
| RFA | B1598:29 | Antenna #12: Signal Invalid | GO to Pinpoint Test C |
| RFA | B1598:31 | Antenna #12: No Signal | GO to Pinpoint Test C |
| RFA | B1598:45 | Antenna #12: Program Memory Failure | GO to Pinpoint Test C |
| RFA | B1598:49 | Antenna #12: Internal Electronic Failure | GO to Pinpoint Test C |
| RFA | B1598:57 | Antenna #12: Invalid/ Incompatible Software Component | GO to Pinpoint Test C |
| RFA | B15A5:56 | Bluetooth Low Energy Module: Invalid/ Incompatible Configuration | GO to Pinpoint Test D |
| RFA | B1A56:29 | Antenna: Signal Invalid | GO to Pinpoint Test A |
| RFA | B1A56:31 | Antenna: No Signal | GO to Pinpoint Test A |
| RFA | B1A56:45 | Antenna: Program Memory Failure | GO to Pinpoint Test A |
| RFA | B1A56:49 | Antenna: Internal Electronic Failure | GO to Pinpoint Test A |
| RFA | B1A56:57 | Antenna: Invalid/ Incompatible Software Component | GO to Pinpoint Test A |
| RFA | B1D55:29 | Antenna #2: Signal Invalid | GO to Pinpoint Test A |
| RFA | B1D55:31 | Antenna #2: No Signal | GO to Pinpoint Test A |
| RFA | B1D55:45 | Antenna #2: Program Memory Failure | GO to Pinpoint Test A |
| RFA | B1D55:49 | Antenna #2: Internal Electronic Failure | GO to Pinpoint Test A |
| RFA | B1D55:57 | Antenna #2: Invalid/ Incompatible Software Component | GO to Pinpoint Test A |
| RFA | P0601:41 | Internal Control Module Memory Checksum Error: General Checksum Failure | GO to Pinpoint Test H |
| RFA | P1269:00 | Immobilizer Code Not Programmed: No Sub Type Information | GO to Pinpoint Test F |
| RFA | P1602:00 | Immobilizer/ ECM Communication Error: No Sub Type Information | GO to Pinpoint Test F |
| RFA | P1622:00 | Immobilizer ID Does Not Match: No Sub Type Information | GO to Pinpoint Test F |
| RFA | P1623:00 | Immobilizer Code Word/ID Number Write Failure: No Sub Type Information | GO to Pinpoint Test F |
| RFA | U0146:00 | Lost Communication With Gateway "A": No Sub Type System | GO to Pinpoint Test I |
| RFA | U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test I |
| RFA | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test F |
| RFA | U1008:00 | Private Communication Network Bus (-) shorted to Bus (+) | GO to Pinpoint Test H |
| RFA | U200D:11 | Control Module Output Power A: Circuit Short to Ground | GO to Pinpoint Test C |
| RFA | U200D:15 | Control Module Output Power A: Circuit Short to Battery or Open | GO to Pinpoint Test C |
| RFA | U200E:11 | Control Module Output Power B: Circuit Short to Ground | GO to Pinpoint Test B |
| RFA | U200E:15 | Control Module Output Power B: Circuit Short to Battery or Open | GO to Pinpoint Test B |
| RFA | U200F:11 | Control Module Output Power C: Circuit Short to Ground | GO to Pinpoint Test A |
| RFA | U200F:15 | Control Module Output Power C: Circuit Short to Battery or Open | GO to Pinpoint Test A |
| RFA | U201A:06 | Control Module Main Calibration Data: Algorithm Based Failure | GO to Pinpoint Test E |
| RFA | U201A:46 | Control Module Main Calibration Data: Calibration/ Parameter Memory failure | GO to Pinpoint Test E |
| RFA | U201A:55 | Control Module Main Calibration Data: Not Configured | GO to Pinpoint Test E |
| RFA | U2100:55 | Initial Configuration Not Complete: Not Configured | GO to Pinpoint Test E |
| RFA | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test H |
| RFA | U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test H |
| RFA | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test H |