DTC Charts

WARNING: This page is about a different variant/trim than selected.

4X4 CONTROL MODULE DTC CHART

DTC	Description	Possible Causes	Source	Action
B1317	Battery Voltage High	Generator	4X4 Control Module	Go to Pinpoint Test B .
B1318	Battery Voltage Low	Blown fuse (B+) Intermittent open on power circuit 4X4 control module connector	4X4 Control Module	CHECK smart junction box (SJB) fuses 11 (10A) and 35 (10A). If fuses are OK, go to Pinpoint Test B .
B1342	ECU is Faulted	Microprocessor or internal memory fault	4X4 Control Module	CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a new 4X4 control module. REFER to 4X4 CONTROL MODULE .
B2900	VIN Mismatch	Incorrect VIN codes received from PCM	4X4 Control Module	CHECK the PCM configuration. REFER to MODULE CONFIGURATION article.
P1635	Tire/Axle Out of Acceptable Range	Incorrect size tire installed on vehicle Wheel speed sensor failure Flat or under-inflated tire	4X4 Control Module	Go to Pinpoint Test G .
P1824	4-Wheel Drive Clutch Relay Circuit Failure	Short to ground on active torque control coupling (ATCC) solenoid (part of rear axle) high circuit 4X4 control module failure	4X4 Control Module	CHECK SJB fuse 11 (10A). If the fuse is OK, go to Pinpoint Test E .
P1825	4-Wheel Drive Clutch Relay Open Circuit	4X4 control module harness connector Open in ATCC solenoid (part of rear axle) low circuit Open in ATCC solenoid high circuit Short to ground on ATCC solenoid low circuit Short to ground on ATCC solenoid high circuit Open coil inside ATCC solenoid Short to voltage in ATCC solenoid low circuit 4X4 control module failure	4X4 Control Module	CHECK SJB fuses 11 (10A) and 35 (10A). If the fuses are OK, go to Pinpoint Test E .
U0100	Lost Communication with ECM/PCM	Controller area network (CAN) bus fault No data received by 4X4 control module from PCM	4X4 Control Module	Go to Pinpoint Test D .
U0121	Lost Communication with Anti-lock Brake System (ABS) Control Module	CAN bus fault No data received by 4X4 control module from ABS control module	4X4 Control Module	Go to Pinpoint Test D .
U0155	Lost Communication with Instrument Cluster (IC) Control Module	High-speed controller area network (HS-CAN) fault No data received from the IC by the 4X4 control module	4X4 Control Module	REFER to MODULE COMMUNICATIONS NETWORK article to diagnose the lost communication with the IC.
U0401	Invalid Data Received From ECM/PCM A	Invalid data received from PCM Data out of range	4X4 Control Module	REFER to Introduction - Gasoline Engines article to diagnose the accelerator position, engine coolant or keep alive memory fault.
U0415	Invalid Data Received From Anti-lock Brake System (ABS) Control Module	Invalid data received from ABS module Data out of range	4X4 Control Module	Go to Pinpoint Test C .
U2050	No Application Present	Application software is not present Application software update failed 4X4 control module failed	4X4 Control Module	CONFIGURE the 4X4 control module. REFER to MODULE CONFIGURATION article to CARRY OUT programmable module installation (PMI). CLEAR the DTCs. RETRIEVE the DTCs and VERIFY successful module configuration. If DTC U2050 is retrieved again, INSTALL a new 4X4 control module. REFER to 4X4 CONTROL MODULE . REPEAT the self-test.
U2051	One or More Calibration Files Missing/Corrupt	Calibration software not present Calibration software update failed 4X4 control module failed	4X4 Control Module	CONFIGURE the 4X4 control module. REFER to MODULE CONFIGURATION article to CARRY OUT PMI. CLEAR the DTCs. RETRIEVE the DTCs and VERIFY successful module configuration. If DTC U2050 is retrieved again, INSTALL a new 4X4 control module. REFER to 4X4 CONTROL MODULE . REPEAT the self-test.