LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Fuel System - Service Information) >> Fuel Pump >> Removal [11/2021 - ] >> Procedure

Removal [11/2021 - ]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350h, 2024 Lexus NX 350h, 2023 Lexus NX 350h, and 2022 Lexus NX 350h. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Refer to BEFORE DISCONNECTING BATTERY [11/2021 - ]
  2. DISCHARGE FUEL SYSTEM PRESSURE 

    Refer to PRECAUTION [11/2021 - ]

  3. REMOVE BATTERY SERVICE COVER PLATE 

    Refer to PROCEDURE - Step 2

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 3

  5. REMOVE REAR SEAT CUSHION ASSEMBLY 
    for Manual Seat: Refer to PROCEDURE - Step 8
    for Power Seat: Refer to PROCEDURE - Step 11
  6. REMOVE REAR SEAT CUSHION LOCK HOOK 

    Refer to PROCEDURE - Step 9

  7. REMOVE REAR DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 21

  8. REMOVE NO. 3 BATTERY SERVICE COVER BOARD 

    Refer to PROCEDURE - Step 23

  9. REMOVE REAR DOOR SCUFF PLATE RH 
    1. Use the same procedure as for the LH side.
  10. REMOVE NO. 2 BATTERY SERVICE COVER BOARD 
    1. Use the same procedure as for the LH side.
  11. REMOVE BATTERY SERVICE COVER BOARD 

    Refer to PROCEDURE - Step 7

  12. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 20 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 20 [03/2022 - 03/2024] , or refer to PROCEDURE - Step 20 [03/2024 - ]
  13. REMOVE REAR FLOOR SERVICE HOLE COVER 
    1. GTY1075426Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Turn back the front floor carpet assembly.
      2. Remove the 3 bolts and rear floor service hole cover from the vehicle body.
      3. Disconnect the 3 connectors from the fuel suction tube with pump and gauge assembly and fuel gauge wire.
  14. REMOVE FUEL TANK PRESSURE SENSOR (VAPOR PRESSURE SENSOR) 
    Refer to PROCEDURE - Step 2 [11/2021 - 03/2024] , or refer to PROCEDURE - Step 2 [03/2024 - ]
  15. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY 
    1. GTY1076106Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the fuel tank vent hose sub-assembly from the fuel suction tube with pump and gauge assembly.

        Refer to PRECAUTION [11/2021 - ]

  16. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY 
    1. GTY1075863Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Tube Joint Clip *2 Fuel Tank Main Tube Sub-assembly
      *a Nylon Tube *b Fuel Tube Joint
      *c Fuel Suction Plate Sub-assembly *d O-ring
      Pull off Pull off
      1. Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
        NOTE:
        • Remove any foreign matter on the fuel tube joint before performing this work.
        • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
        • Be sure to disconnect the fuel tube joint by hand.
        • Do not bend, twist, pinch or kink the nylon tube.
        • Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
        • If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.
  17. REMOVE FUEL GAGE WIRE 
    1. GTY1075409Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE NO. 1 FUEL TUBE CLAMP 
    1. for Type A
      GTY1075406Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for Type B
      GTY1254414Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE FUEL PUMP GAUGE RETAINER 
    1. GTY1075064Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a SST (Plate) *b SST (Bolt)
      *c SST (Claw) *d SST (Handle)
      *e Insertion Point - -
      1. Remove the fuel pump gauge retainer.

        1. Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

        • SST: 09808-01071 
        • SST: 09808-14031 
          1. 09808-01030
          2. 09808-01090

        HINT: 

        Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.

        2. While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).

        3. Install SST (handle) to SST (plate).

        • SST: 09808-14031 
          1. 09808-01010

        4. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

        NOTE:
        • Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank sub-assembly.
        • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
        • Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
        • Do not spin SST too fast or use an impact wrench as this may result in damage to components.
        • If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

        5. While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.

  20. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 
    1. GTY1076015Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank sub-assembly.
        NOTE:

        Be careful not to bend the arm of the fuel sender gauge assembly.

  21. REMOVE FUEL SUCTION TUBE SET GASKET 
    1. GTY1065981Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals