LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2025 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 48 (Engine Mechanical System - Service Information (1 Of 4)) >> Camshaft >> Removal [11/2021 - 03/2024] >> Procedure

Removal [11/2021 - 03/2024]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350, 2024 Lexus NX 350, 2023 Lexus NX 350, and 2022 Lexus NX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND 

    Refer to REMOVAL [11/2021 - 03/2023] , or refer to REMOVAL [03/2023 - 03/2024]

  2. REMOVE ENGINE HANGERS 
  3. REMOVE NO. 2 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 4

  4. REMOVE PURGE VALVE (PURGE VSV) 

    Refer to PROCEDURE - Step 13

  5. DISCONNECT NO. 1 VENTILATION PRESSURE SENSOR HOSE 

    Refer to PROCEDURE - Step 4

  6. REMOVE AIR TUBE ASSEMBLY 
    Refer to PROCEDURE - Step 8
  7. DISCONNECT NO. 2 FUEL VAPOR FEED HOSE 

    Refer to PROCEDURE - Step 10

  8. REMOVE VACUUM REGULATING VALVE ASSEMBLY 

    Refer to PROCEDURE - Step 17

  9. REMOVE COMPRESSOR INLET ELBOW SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 18
  10. DISCONNECT NO. 2 TURBO WATER HOSE 

    Refer to PROCEDURE - Step 22

  11. DISCONNECT NO. 3 TURBO WATER HOSE 

    Refer to PROCEDURE - Step 23

  12. DISCONNECT WATER OUTLET STAY 

    Refer to PROCEDURE - Step 29

  13. DISCONNECT FUEL TUBE SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 10 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 11 [03/2023 - ]
  14. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 11 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 12 [03/2023 - ]
  15. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY 
    Refer to PROCEDURE - Step 12 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 13 [03/2023 - ]
  16. REMOVE FUEL PUMP SPACER GASKET 

    Refer to PROCEDURE - Step 13 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 14 [03/2023 - ]

  17. REMOVE FUEL PUMP LIFTER ASSEMBLY 

    Refer to PROCEDURE - Step 14 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 15 [03/2023 - ]

  18. REMOVE IGNITION COIL ASSEMBLY 
    Refer to PROCEDURE - Step 3 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 4 [03/2023 - ]
  19. REMOVE CONVERTER WITH CATALYST ASSEMBLY 

    Refer to REMOVAL [11/2021 - 03/2024]

  20. REMOVE EXHAUST PIPE HEAT INSULATOR 

    Refer to PROCEDURE - Step 2

  21. REMOVE WATER BY-PASS HOSE 

    Refer to PROCEDURE - Step 46

  22. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 47

  23. REMOVE WATER BY-PASS GASKET 

    Refer to PROCEDURE - Step 48

  24. REMOVE NO. 1 HEAT INSULATOR BRACKET 

    Refer to PROCEDURE - Step 24

  25. REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY 
    Refer to PROCEDURE - Step 3
  26. REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side) 
    Refer to PROCEDURE - Step 2
  27. REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side) 
    Refer to PROCEDURE - Step 3
  28. REMOVE CAM TIMING OIL CONTROL SOLENOID O-RING 
    Refer to PROCEDURE - Step 4
  29. REMOVE VACUUM PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 7 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 8 [03/2023 - ]

  30. REMOVE NO. 1 VACUUM PUMP O-RING 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 9 [03/2023 - ]

  31. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 3
  32. REMOVE DIRECT FUEL INJECTOR ASSEMBLY 
    Refer to PROCEDURE - Step 4
  33. REMOVE NOZZLE HOLDER CLAMP 

    Refer to PROCEDURE - Step 5

  34. REMOVE NO. 3 FUEL INJECTOR BACK-UP RING 
    Refer to PROCEDURE - Step 6
  35. REMOVE NO. 1 FUEL INJECTOR BACK-UP RING 

    Refer to PROCEDURE - Step 7

  36. REMOVE C-RING 

    Refer to PROCEDURE - Step 8

  37. REMOVE INJECTOR VIBRATION INSULATOR 

    Refer to PROCEDURE - Step 9

  38. REMOVE FUEL INJECTOR SEAL 
    Refer to PROCEDURE - Step 10
  39. REMOVE CRANKSHAFT PULLEY ASSEMBLY 
    Refer to PROCEDURE - Step 23
  40. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side) 
    Refer to PROCEDURE - Step 2 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 3 [03/2023 - ]
  41. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side) 
    Refer to PROCEDURE - Step 3 [11/2021 - 03/2023] , or refer to PROCEDURE - Step 4 [03/2023 - ]
  42. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 26
  43. REMOVE SPARK PLUG TUBE GASKET 
    Refer to PROCEDURE - Step 27
  44. REMOVE INJECTOR HOLDER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 28

  45. REMOVE ENGINE MOUNTING BRACKET RH 
    Refer to PROCEDURE - Step 29
  46. REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY 
    Refer to PROCEDURE - Step 31
  47. REMOVE TIMING CHAIN CASE OIL SEAL 
    Refer to PROCEDURE - Step 32
  48. SET NO. 1 CYLINDER TO TDC (COMPRESSION) 
    Refer to PROCEDURE - Step 33
  49. REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 34
  50. REMOVE NO. 2 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 35

  51. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 
    Refer to PROCEDURE - Step 36
  52. REMOVE CHAIN TENSIONER SLIPPER 

    Refer to PROCEDURE - Step 37

  53. REMOVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 38

  54. REMOVE NO. 1 CHAIN VIBRATION DAMPER 

    Refer to PROCEDURE - Step 39

  55. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY 
    Refer to PROCEDURE - Step 40
  56. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY 
    Refer to PROCEDURE - Step 41
  57. REMOVE TIMING CHAIN COVER ASSEMBLY 
    Refer to PROCEDURE - Step 42
  58. REMOVE FUEL PUMP LIFTER GUIDE 
    Refer to PROCEDURE - Step 44
  59. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY 
    Refer to PROCEDURE - Step 45
  60. REMOVE CAMSHAFT BEARING CAP 
    Refer to PROCEDURE - Step 46
  61. REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY 
    1. GTY1076912Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  62. REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY 
    1. GTY1076913Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  63. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 49

  64. REMOVE VALVE LASH ADJUSTER ASSEMBLY 

    Refer to PROCEDURE - Step 50

  65. REMOVE VALVE STEM CAP 

    Refer to PROCEDURE - Step 51

scientia non olet · About LEMON Manuals