LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> RX 500h >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information (2 Of 2) >> Roof Headlining >> Removal [08/2023 - ] >> Procedure

Removal [08/2023 - ]: Procedure

  1. REMOVE TONNEAU COVER ASSEMBLY 
    1. GTY1137883Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE DECK BOARD ASSEMBLY 
    1. GTY1137884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE BATTERY SERVICE COVER PLATE (except Gasoline Model) 
    1. GTY1205670Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A w/o Spare Tire *B w/ Spare Tire
  4. REMOVE REAR DECK FLOOR BOX (for Gasoline Model) 
    1. GTY1204687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A w/o Spare Tire *B w/ Spare Tire
  5. REMOVE REAR DECK FLOOR BOX LH 
    1. GTY1204877Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A w/o Spare Tire *B w/ Spare Tire
  6. REMOVE REAR FLOOR BOARD REAR RH 
    1. GTY1137792Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for Gasoline Model *B except Gasoline Model
  7. REMOVE JUNCTION BLOCK SERVICE COVER (except Gasoline Model) 
    1. GTY1137893Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE REAR FLOOR BOARD REAR LH 
    1. GTY1133884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE JUNCTION BLOCK SERVICE COVER LH 
    1. GTY1137896Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE DECK FLOOR BOX LH (w/o Spare Tire) 
    1. GTY1203796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE DECK FLOOR BOX RH 
    1. GTY1203598Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A w/o Spare Tire *B w/ Spare Tire
  12. SEPARATE REAR SEATBACK ASSEMBLY RH 

    Refer to PROCEDURE - Step 13

  13. SEPARATE REAR SEATBACK ASSEMBLY LH 

    Refer to PROCEDURE - Step 14

  14. REMOVE DECK BOARD SET SUPPORT LH 
    1. GTY1137891Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE DECK BOARD SET SUPPORT 
    1. GTY1137892Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [08/2023 - ]

  17. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. GTY1126303Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction (1)
      Remove in this Direction (2) - -
  18. REMOVE COWL SIDE TRIM BOARD LH 
    1. GTY1125097Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  19. REMOVE NO. 2 INSTRUMENT SIDE PANEL 
    Refer to PROCEDURE - Step 11
  20. REMOVE FRONT PILLAR GARNISH ASSEMBLY LH 
    1. GTY1125252Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Pull in this Direction - -
      1. Pull the upper part of the front pillar garnish LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish LH from the base of the 2 front pillar garnish clips.

        HINT: 

        Let the front pillar garnish LH hang from the 2 front pillar garnish clips.

    2. GTY1123616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Pull in this Direction Pull in this Direction
      1. Pull down the front pillar garnish clip while pushing the side of the release lever with SST as shown in the illustration.
        • SST: 09813-00020 
      2. While pulling the front pillar garnish clip, push the side of the release lever with SST as shown in the illustration and then separate the front pillar garnish clip from the vehicle body.
    3. GTY1128206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      1. Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
    4. GTY1126287Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Protect the curtain shield airbag assembly LH.

        1. Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.

        NOTE:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

    5. GTY1128957Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 2 front pillar garnish clips from the front pillar garnish LH.
  21. REMOVE REAR DOOR SCUFF PLATE LH 
    1. GTY1128354Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
    2. GTY1127664Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
    3. GTY1125783Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  22. REMOVE NO. 3 BATTERY SERVICE COVER BOARD 
    1. GTY1122931Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
    2. w/ Rear Power Seat System:
      GTY1136038Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) 

    Refer to PROCEDURE - Step 10

  24. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 11

  25. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 7

  26. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH 
    1. for Center Piller Garnish Assembly LH Side:

      Refer to PROCEDURE - Step 9

    2. for Rear Seat Side Garnish LH Side:

      Refer to PROCEDURE - Step 28

  27. REMOVE CENTER PILLAR LOWER GARNISH LH 
    1. GTY1129177Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
  28. REMOVE CENTER PILLER GARNISH ASSEMBLY LH 
    1. GTY1124899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  29. REMOVE FRONT DOOR SCUFF PLATE RH 
    1. Use the same procedure as for the LH side.
  30. REMOVE COWL SIDE TRIM BOARD RH 
    1. Use the same procedure as for the LH side.
  31. REMOVE NO. 1 INSTRUMENT SIDE PANEL 
    Refer to PROCEDURE - Step 23
  32. REMOVE FRONT PILLAR GARNISH ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  33. REMOVE REAR DOOR SCUFF PLATE RH 
    1. Use the same procedure as for the LH side.
  34. REMOVE NO. 2 BATTERY SERVICE COVER BOARD 
    1. Use the same procedure as for the No. 3 battery service cover board.
  35. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) 
    1. Use the same procedure as for the LH side.
  36. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  37. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Use the same procedure as for the LH side.
  38. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Use the same procedure as for the LH side.
  39. REMOVE CENTER PILLAR LOWER GARNISH RH 
    1. Use the same procedure as for the LH side.
  40. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  41. REMOVE REAR SEAT SIDE GARNISH LH 
    1. GTY1124893Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction (1)
      Remove in this Direction (2) - -
  42. REMOVE REAR FLOOR FINISH PLATE 
    1. GTY1137853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  43. REMOVE ROPE HOOK ASSEMBLY (for LH Side) 
    1. GTY1127610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and open the cover.
      2. Remove the bolt and rope hook assembly.
    2. Remove using the same procedure as for the rear side.
  44. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side) 
    1. GTY1128276Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Rotation Direction Remove in this Direction
  45. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side) 
    Refer to PROCEDURE - Step 1
  46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. GTY1126389Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Lower the No. 1 deck side trim hook as shown in the illustration.
    2. GTY1125079Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Push in this Direction - -
      1. Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.
    3. GTY1122990Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 2 bolts.
      2. Disengage the 2 clips, 5 claws and 4 guides to remove the deck trim side panel assembly LH.
    4. GTY1134116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the connector.
    5. GTY1136291Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect each connector.
  47. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 38

  48. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH 
    1. GTY1126102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. GTY1125547Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  49. REMOVE REAR SEAT SIDE GARNISH RH 
    1. Use the same procedure as for the LH side.
  50. REMOVE ROPE HOOK ASSEMBLY (for RH Side) 
    1. Use the same procedure as for the LH side.
  51. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side) 
    1. Use the same procedure as for the LH side.
  52. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side) 
    1. Use the same procedure as for the LH side.
  53. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 
    1. GTY1123979Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Lower the No. 1 deck side trim hook as shown in the illustration.
    2. GTY1122628Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Push in this Direction - -
      1. Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.
    3. GTY1122610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 2 bolts.
      2. Disengage the 2 clips, 5 claws and 4 guides to remove the deck trim side panel assembly LH.
    4. w/ Power Outlet Socket:
      GTY1129262Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the connector.
  54. REMOVE REAR NO. 2 POWER OUTLET SOCKET ASSEMBLY (w/ Power Outlet Socket) 

    Refer to PROCEDURE - Step 12

  55. REMOVE POWER OUTLET SOCKET BEZEL (w/ Power Outlet Socket) 
    1. GTY1124286Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  56. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  57. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  58. REMOVE VISOR BRACKET COVER LH 
    1. GTY1126096Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  59. REMOVE VISOR ASSEMBLY LH 
    1. GTY1126095Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  60. REMOVE VISOR BRACKET COVER RH 
    1. Use the same procedure as for the LH side.
  61. REMOVE VISOR ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  62. REMOVE ASSIST GRIP COVER 
    1. GTY1135710Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 30 to 45° - -
      Remove in this Direction - -
      1. Insert SST into the cutout of the assist grip cover as shown in the illustration.
        • SST: 09813-00010 
        NOTE:

        To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      2. Pull SST as shown in the illustration to disengage the claw.
        NOTE:

        To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

        HINT: 

        Use the same procedure for the claw on the other side of the assist grip cover.

      3. Remove the assist grip cover.
    2. Use the same procedure for all assist grip covers.
  63. REMOVE ASSIST GRIP 
    1. GTY1124147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for LH Side *B for RH Side
      Remove in this Direction - -
  64. REMOVE REAR ASSIST GRIP LH 
    1. Use the same procedure as for the assist grip.
  65. REMOVE REAR ASSIST GRIP RH 
    1. Use the same procedure as for the assist grip.
  66. REMOVE FRONT ROOF HEADLINING TRIM 
    1. GTY1137938Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      1. Using a moulding remover, disengage the claw as shown in the illustration.
    2. GTY1137256Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
      1. Disengage the 3 claws as shown in the illustration.
    3. GTY1136496Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      1. Disengage the guide to remove the front roof headlining trim as shown in the illustration.
  67. REMOVE MAP LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 2

  68. REMOVE VANITY LIGHT ASSEMBLY 
    Refer to PROCEDURE - Step 1
  69. REMOVE NO. 1 ROOM LIGHT ASSEMBLY 
    Refer to PROCEDURE - Step 1
  70. REMOVE NO. 2 FORWARD RECOGNITION COVER 
    Refer to PROCEDURE - Step 2
  71. REMOVE NO. 1 FORWARD RECOGNITION COVER 
    Refer to PROCEDURE - Step 3
  72. REMOVE RAIN SENSOR 

    Refer to REMOVAL [10/2022 - ]

  73. REMOVE ROOF HEADLINING ASSEMBLY 
    1. GTY1129134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Move in This Direction Recline in This Direction
      1. Operate the power seat switch knob (slide and vertical) and slide the front seat assembly LH to the front most position.
      2. Operate the power seat switch knob (reclining) and recline the seatback of the front seat assembly LH to the operational limit position.
    2. Perform the same procedure as for the opposite side.
    3. GTY1126282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      As the illustration shown is an example, the actual details may differ.

      1. for Front Pillar LH Side:

        1. Remove the protective cover.

        2. Disconnect each connector.

        3. Disengage the 3 clamps.

        4. Disconnect the washer hose assembly.

        5. Install the protective cover.

      2. for Front Pillar RH Side:

        1. Remove the protective cover.

        2. Disconnect each connector.

        3. Disengage the 2 clamps.

        4. Install the protective cover.

      3. for Windshield Glass Side:

        1. Disconnect each connector.

      4. for Map Light Side:

        1. Disconnect the connector.

      5. for Rear Pillar LH Side with Digital Inner Mirror:

        1. Disconnect the connector.

      6. for Rear Pillar RH Side:

        1. Disconnect each connector.

    4. GTY1135393Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Rotation Direction Remove in this Direction (1)
      Remove in this Direction (2) - -
      1. Turn each visor holder approximately 45° and remove them as indicated by the arrows, in the order shown in the illustration.
      2. Disengage the 4 claws as shown in the illustration to remove the base of each visor holder.
    5. for Normal Roof:
      GTY1137624Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener - -
      Remove in this Direction - -
      1. Disengage the 13 clips.
      2. Disengage the 2 fasteners.
      3. Disconnect the rear side of the washer hose assembly and remove the roof headlining assembly.
      4. Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
        NOTE:

        Do not damage the roof headlining assembly or vehicle interior.

    6. for Moon Roof:
      GTY1136838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener *b Guide
      Remove in this Direction - -
      1. Disengage the 13 clips.
      2. Disengage the 7 fasteners and guide.
      3. Disconnect the rear side of the washer hose assembly and remove the roof headlining assembly.
      4. Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
        NOTE:

        Do not damage the roof headlining assembly or vehicle interior.

    7. for Panoramic Moon Roof:
      GTY1136165Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener *b Guide
      Remove in this Direction - -
      1. Disengage the 13 clips.
      2. Disengage the 14 fasteners and guide.
      3. Disconnect the rear side of the washer hose assembly and remove the roof headlining assembly.
      4. Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
        NOTE:

        Do not damage the roof headlining assembly or vehicle interior.

scientia non olet · About LEMON Manuals