LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2024 >> NX 250 FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 64 (Hybrid Battery Control System - Service Information (2 Of 2)) >> Sub Radiator >> Removal [11/2021 - 03/2024] >> Procedure

Removal [11/2021 - 03/2024]: Procedure

WARNING: This page is about a different car, the 2025 Lexus NX 350h, 2024 Lexus NX 350h, 2023 Lexus NX 350h, and 2022 Lexus NX 350h. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE RADIATOR ASSEMBLY (for Inverter Coolant for Type A) 
    HINT: 
    The radiator (for inverter coolant) is part of the radiator (for Engine). If the radiator (for inverter coolant) needs to be replaced, replace the radiator assembly.

    Refer to REMOVAL [11/2021 - 03/2024]

  2. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH (for Type B) 

    Refer to PROCEDURE - Step 7

  3. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH (for Type B) 

    Refer to PROCEDURE - Step 8

  4. REMOVE NO. 1 ENGINE UNDER COVER (for Type B) 

    Refer to PROCEDURE - Step 9

  5. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (for Type B) 

    Refer to PROCEDURE - Step 10

  6. DRAIN COOLANT (for Type B) 

    Refer to PROCEDURE - Step 1

  7. REMOVE FRONT BUMPER ASSEMBLY (for Type B) 

    for Sport Package: Refer to REMOVAL [11/2021 - 03/2024]

    except Sport Package: Refer to REMOVAL [11/2021 - 03/2024]

  8. REMOVE FRONT NO. 2 BUMPER ENERGY ABSORBER (for Type B) 

    Refer to PROCEDURE - Step 45 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 46 [03/2022 - ]

  9. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (for Type B) 

    Refer to PROCEDURE - Step 50 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 51 [03/2022 - ]

  10. REMOVE HEADLIGHT ASSEMBLY LH (for Type B) 

    for LED Type Turn Signal Light: Refer to REMOVAL [11/2021 - ]

    for Bulb Type Turn Signal Light: Refer to REMOVAL [11/2021 - ]

  11. REMOVE HEADLIGHT ASSEMBLY RH (for Type B) 
    1. Use the same procedure as for the LH side.
  12. REMOVE INLET AIR CLEANER ASSEMBLY (for Type B) 

    Refer to PROCEDURE - Step 4

  13. REMOVE HOOD SUPPORT TENSION SPRING (for Type B) 
    Refer to PROCEDURE - Step 3 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 3 [03/2022 - ]
  14. REMOVE HOOD LOCK CONTROL COVER (for Type B) 

    Refer to PROCEDURE - Step 8 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 8 [03/2022 - ]

  15. DISCONNECT HOOD LOCK CONTROL CABLE AND LEVER SET (for Type B) 

    Refer to PROCEDURE - Step 9 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 9 [03/2022 - ]

  16. REMOVE HOOD LOCK CONTROL JUNCTION ASSEMBLY (for Type B) 

    Refer to PROCEDURE - Step 10 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 10 [03/2022 - ]

  17. REMOVE HOOD LOCK ASSEMBLY LH (for Type B) 

    Refer to PROCEDURE - Step 11 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 11 [03/2022 - ]

  18. REMOVE HOOD LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (for Type B) 

    Refer to PROCEDURE - Step 12 [11/2021 - 03/2022] , or refer to PROCEDURE - Step 12 [03/2022 - ]

  19. REMOVE NO. 2 RADIATOR TO SUPPORT SEAL (for Type B) 

    Refer to PROCEDURE - Step 8

  20. REMOVE NO. 3 RADIATOR TO SUPPORT SEAL (for Type B) 

    Refer to PROCEDURE - Step 9

  21. REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH (for Type B) 

    Refer to PROCEDURE - Step 10

  22. REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH (for Type B) 

    Refer to PROCEDURE - Step 11

  23. REMOVE THERMISTOR ASSEMBLY (for Type B) 

    Refer to REMOVAL [11/2021 - ]

  24. REMOVE NO. 1 RADIATOR AIR GUIDE LH (for Type B) 

    Refer to PROCEDURE - Step 24

  25. DISCONNECT NO. 3 INVERTER COOLING HOSE (for Type B) 
    NOTE:
    • Put pieces of cloth into the pipes and disconnected hoses or cover the pipes and hoses with plastic bags to prevent foreign matter from entering the radiator assembly (for inverter coolant) and inverter cooling system.
    • Do not apply excessive force to the No. 3 inverter cooling hose.
    1. GTY1078656Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE NO. 1 RADIATOR AIR GUIDE RH (for Type B) 

    Refer to PROCEDURE - Step 26

  27. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for Type B) 

    Refer to PROCEDURE - Step 27

  28. REMOVE RADIATOR ASSEMBLY (for Type B) 
    1. GTY1078111Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Slide the clip and disconnect the No. 4 inverter cooling hose from the radiator assembly (for inverter coolant).
        NOTE:
        • Put pieces of cloth into the pipes and disconnected hoses or cover the pipes and hoses with plastic bags to prevent foreign matter from entering the radiator assembly (for inverter coolant) and inverter cooling system.
        • Do not apply excessive force to the No. 4 inverter cooling hose.
      2. Remove the 4 bolts.
      3. Disengage the 2 claws and remove the radiator assembly (for inverter coolant) from the radiator assembly.
scientia non olet · About LEMON Manuals