Installation [05/2023 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL ROOF SIDE RAIL GARNISH

Attach the clamps to install the roof side rail garnish.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

HINT:

Use the same procedure for the opposite side.

INSTALL ROOF HEADLINING ASSEMBLY

Install a new grommet to the vehicle.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedure for the RH side.

Install the 3 clips to the roof headlining assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Clip (White)
*b	Clip (Black)
	Install in this Direction

Install the roof headlining:

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Carry the roof headlining assembly through the passenger door into the vehicle as shown in the illustration without making contact with the body interior.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

NOTE:

The procedure must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining assembly are free of bending, twisting and other deformation and that none of the mounted parts are falling off.
Do not damage the roof headlining assembly and body interior.

Attach the clips.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

for Glass Roof:

Attach the fasteners.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

for Carbon Roof:

Attach the fasteners.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Attach the claws to install the roof headlining assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

HINT:

Check that the front roof side rail weatherstrip is not pinched between the roof headlining assembly and body.
Use the same procedure for the opposite side.

Install the screw to the coat hook.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedure for the opposite side.

Front pillar LH part:

Remove the protective cover installed to the front pillar LH.

Connect the 2 connectors.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Attach the clamps to connect the No. 1 roof wire.
Install the protective cover to the front pillar LH.

Connect the 2 connectors.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL VISOR HOLDER

HINT:

Use the same procedure for the opposite side.

Attach the claws as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Push in the end of the visor holder to install the visor holder.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

INSTALL RAIN SENSOR COVER
Refer to PROCEDURE - Step 3
INSTALL MAP LIGHT ASSEMBLY
Refer to INSTALLATION [05/2023 - ]

INSTALL VISOR ASSEMBLY LH

Align the visor assembly LH and the vehicle side connector and screw hole to set it in place.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

NOTE:

Set the visor assembly LH directly upwards so that the connector is not damaged.
Hold the visor assembly with one hand so that it does not drop.

Install the 2 screws.
Set the visor assembly LH to the visor holder LH.

INSTALL VISOR ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

INSTALL VISOR BRACKET COVER

HINT:

Use the same procedure for the opposite side.

Attach the claws to install the visor bracket cover.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH

Peel off the adhesive tape and remove the protective cover.

Attach the 2 inner upper roof side garnish clips to the inner roof side garnish assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NOTE:

If there is extreme damage to the inner upper roof side garnish clip, replace it with a new one.
Make sure that the position and direction of the inner upper roof side garnish clip is correct when installing.

Insert the guides in direction indicated by the arrow shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Attach the inner upper roof side garnish clips in the direction of the arrow shown in the illustration to install the inner roof side garnish assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

Attach the roof side trim garnish clip to the roof side rail garnish assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NOTE:

If there is extreme damage to the roof side trim garnish clip, replace it with a new one.
Make sure that the position and direction of the roof side trim garnish clip is correct when installing.

Attach the roof side trim garnish clip and clips in the direction of the arrow shown in the illustration to install the roof side rail garnish assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

INSTALL INNER ROOF SIDE GARNISH LH

Attach the clips in the direction of the arrow shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Attach the clips in the direction of the arrow shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Place hand here
	Install in this Direction

Place your hand at the position shown in the illustration, attach the claw and install the roof side inner garnish LH as shown in the illustration.

INSTALL INNER ROOF SIDE GARNISH RH
HINT:

Use the same procedure described for the LH side.

INSTALL CENTER PILLAR GARNISH ASSEMBLY LH

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Pass the seat belt guide LH and front seat outer belt assembly LH (floor anchor) through the center pillar garnish assembly LH.

Push in the guides in the direction of the arrow shown in the illustration and attach the claws to install the seat belt guide LH.

Attach the claw and clip in the installation direction shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Insert the hooks from direction indicated by the arrow shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Install the center pillar garnish assembly LH with the 2 clips.

INSTALL CENTER PILLAR GARNISH ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.

INSTALL QUARTER TRIM PANEL ASSEMBLY LH

Connect the connector.

Attach the clip in the direction of the arrow shown in the illustration.

Install in this Direction

Attach the clips in the direction of the arrow shown in the illustration.

Install in this Direction

Install in this Direction

Attach the claws in the direction of the arrow shown in the illustration.

Attach the clip and claws in the direction of the arrow shown in the illustration.

Install in this Direction

Attach the clip and claws in the direction of the arrow shown in the illustration.

Install in this Direction

Attach the hook to install the quarter trim panel assembly LH.

Install the 2 clips.

Attach the clamp.

INSTALL QUARTER TRIM PANEL ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.
INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
Refer to PROCEDURE - Step 1
INSTALL REAR SEAT INNER BELT ASSEMBLY RH
HINT:

Use the same procedure as for the rear seat No. 1 inner belt assembly LH.

INSTALL QUARTER INSIDE TRIM BOARD LH

Attach the claw in the direction of the arrow shown in the illustration to install the quarter inside trim board LH.

Install in this Direction

INSTALL QUARTER INSIDE TRIM BOARD RH
HINT:

Use the same procedure described for the LH side.
INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)
Refer to PROCEDURE - Step 6
INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)
HINT:

Use the same procedure described for the LH side.
INSTALL OUTER LAP BELT ANCHOR COVER
Refer to PROCEDURE - Step 7

INSTALL FRONT PILLAR GARNISH LH

Peel off the adhesive tape and remove the protective cover.

Install the front pillar garnish clip to the front pillar garnish LH.

NOTE:

If there is extreme damage to the front pillar garnish clip, replace it with a new one.
Make sure that the position and direction of the front pillar garnish clip is correct when installing.

Insert the guides as shown in the illustration.

Install in this Direction

Attach the clip as shown in the illustration.

Install in this Direction

Attach the front pillar garnish clip to install the front pillar garnish LH.

INSTALL FRONT PILLAR GARNISH RH
HINT:

Use the same procedure described for the LH side.
INSTALL FRONT DOOR NO. 2 OPENING TRIM COVER LH
See step 36
INSTALL FRONT DOOR NO. 2 OPENING TRIM COVER RH
See step 37
INSTALL FRONT DOOR OPENING TRIM COVER LH
See step 38
INSTALL FRONT DOOR OPENING TRIM COVER RH
HINT:

Use the same procedure described for the LH side.
INSTALL FRONT DOOR SCUFF PLATE LH
See step 40
INSTALL FRONT DOOR SCUFF PLATE RH
HINT:

Use the same procedure described for the LH side.
INSTALL NO. 1 CONSOLE BOX SUPPORT
Refer to PROCEDURE - Step 3
INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
Refer to INSTALLATION [03/2017 - ]
INSTALL REAR SEAT ASSEMBLY
Refer to INSTALLATION [03/2017 - ]
INSTALL FRONT SEAT ASSEMBLY LH
Refer to INSTALLATION [05/2023 - ]
INSTALL FRONT SEAT ASSEMBLY RH
HINT:

Use the same procedure described for the LH side.
INITIALIZATION OF SEAT ECU
Refer to PROCEDURE - Step 2
INSPECT SRS WARNING LIGHT
Refer to OPERATION CHECK [04/2020 - ]
INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Refer to AUTOMATIC LEARNING CHART [05/2023 - ]