LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Continuously Variable Transaxle (CVT) System (K120) (Service Information) (2 Of 2) >> Park / Neutral Position Switch >> Installation [10/2018 - 07/2022] >> Procedure

Installation [10/2018 - 07/2022]: Procedure

  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.
    2. Temporarily install the transmission control shaft lever to the manual valve lever shaft.
      GTY845794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
      GTY879839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a N
      NOTE:

      If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.

      GTY937286Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Transmission Control Shaft Lever
      *a Manual Valve Link Lever Sub-assembly
      *b Manual Valve
    4. Remove the transmission control shaft lever from the manual valve lever shaft.
    5. Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
      GTY863860Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protrusion
    6. Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

      Torque: 5.4 N.m (55 kgf/cm, 48 in.lbf) 

    7. Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

      Torque: 12.7 N.m (130 kgf/cm, 9 ft.lbf) 

      NOTE:

      Be careful of the direction of the transmission control shaft lever.

    8. Connect the park/neutral position switch connector.
  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY 
    NOTE:

    Before connecting the transmission control cable assembly, check that the shift lever is in N.

    1. Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
      GTY879839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a N
      NOTE:

      If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.

      GTY937286Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Transmission Control Shaft Lever
      *a Manual Valve Link Lever Sub-assembly
      *b Manual Valve
    2. Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
    3. Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.
      GTY777489Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Correct
      *b Incorrect
  3. INSTALL BATTERY CLAMP 

    See step [10/2018 - 08/2021] 35 , or see step [08/2021 - 07/2022] 34

  4. INSTALL ECM 

    Refer to INSTALLATION [10/2018 - 07/2022]

  5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 5

  6. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 3

  7. INSTALL NO. 1 AIR CLEANER INLET 

    Refer to PROCEDURE - Step 18 [10/2018 - 10/2019] , or refer to PROCEDURE - Step 17 [10/2019 - 07/2022]

  8. INSTALL RADIATOR SUPPORT OPENING COVER 

    Refer to PROCEDURE - Step 2

  9. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 41 [10/2018 - 08/2021] , or refer to PROCEDURE - Step 41 [08/2021 - 07/2022]

  10. INSTALL AUXILIARY BATTERY 

    Refer to PROCEDURE - Step 1

  11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 2

    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [10/2018 - 07/2022]

  12. INSPECT SHIFT LEVER POSITION 

    See step  2

  13. ADJUST SHIFT LEVER POSITION 

    See step  3

  14. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY 

    See step  2

  15. ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY 

    See step  5

scientia non olet · About LEMON Manuals