LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Service Information) (1 Of 2) >> KNEE AIRBAG ASSEMBLY (for Driver Side) >> Removal [07/2022 - ] >> Procedure

Removal [07/2022 - ]: Procedure

  1. PRECAUTION 
    WARNING:

    Be sure to read precaution thoroughly before servicing.

    Refer to PRECAUTION [07/2022 - ]

    GTY824211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [07/2022 - ]

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to REMOVAL [07/2022 - ]

    WARNING:
    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
    • If the airbag deploys for any reason, it may cause a serious accident.
    GTY684647Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [07/2022 - ]

  3. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 4

  4. REMOVE NO. 2 INSTRUMENT SIDE PANEL 

    HINT: 

    Use the same procedure as for the LH side.

    Refer to PROCEDURE - Step 10

  5. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    See step  5

  6. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 8

  7. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY 

    Refer to PROCEDURE - Step 9

  8. REMOVE LOWER INSTRUMENT CENTER COVER 

    Refer to PROCEDURE - Step 14

  9. REMOVE LOWER INSTRUMENT PANEL FINISH CENTER PANEL 

    Refer to PROCEDURE - Step 15

  10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  11. REMOVE INSTRUMENT PANEL FINISH PANEL 

    Refer to PROCEDURE - Step 16

  12. REMOVE NO. 1 INSTRUMENT SIDE PANEL 

    Refer to PROCEDURE - Step 10

  13. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 11

  14. REMOVE LOWER INSTRUMENT COVER 

    Refer to PROCEDURE - Step 12

  15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 13

  16. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 
    WARNING:
    GTY817222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Deployment Side
    • When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
    • If the airbag deploys for any reason, it may cause a serious accident.
    1. Check that the ignition switch is off.
    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
      WARNING:
      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
      • If the airbag deploys for any reason, it may cause a serious accident.
    3. Remove the 2 bolts.
      GTY813794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disengage the claws to separate the lower No. 1 instrument panel airbag assembly.
      NOTE:

      When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
      NOTE:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      HINT: 

      Refer to How to Connect or Disconnect Airbag Connector: Refer to HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR [10/2018 - ]

scientia non olet · About LEMON Manuals