LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> IS 350 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 93 (Engine Lubrication System (2GR-FSE) - Service Information) >> Oil Pump >> Removal [04/2013 - 10/2017] >> Procedure

Removal [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL ENGINE TO ENGINE STAND 

    Refer to REMOVAL [04/2013 - 08/2015] , or refer to REMOVAL [08/2015 - 10/2016] , or refer to REMOVAL [10/2016 - 10/2017]

  2. REMOVE ENGINE WIRE 

    Refer to PROCEDURE - Step 13

  3. REMOVE FUEL PUMP ASSEMBLY (for High Pressure) 

    Refer to REMOVAL [04/2013 - 10/2017]

  4. REMOVE V-RIBBED BELT 

    Refer to PROCEDURE - Step 4

  5. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 10

  6. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 2WD) 

    Refer to PROCEDURE - Step 7 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 9 [08/2015 - 10/2017]

  7. REMOVE OIL FILTER BRACKET (for AWD) 

    Refer to PROCEDURE - Step 7 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 7 [08/2015 - 10/2017]

  8. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for AWD) 

    Refer to PROCEDURE - Step 9 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 9 [08/2015 - 10/2017]

  9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 
    1. For 2WD:
      1. Remove the 5 bolts and V-ribbed belt tensioner assembly.
        GTY402838Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. For AWD:
      1. Remove the 4 bolts and V-ribbed belt tensioner assembly.
        GTY105268Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 12

  11. REMOVE WATER PUMP PULLEY 

    Refer to PROCEDURE - Step 10

  12. REMOVE NO. 1 ENGINE COVER 

    Refer to PROCEDURE - Step 6

  13. REMOVE INJECTOR DRIVER 

    Refer to PROCEDURE - Step 7

  14. REMOVE NO. 2 ENGINE COVER 

    Refer to PROCEDURE - Step 2

  15. REMOVE WATER INLET ASSEMBLY 

    Refer to PROCEDURE - Step 29

  16. REMOVE CRANKSHAFT PULLEY 

    Refer to PROCEDURE - Step 4

  17. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 35

  18. REMOVE OIL STRAINER WITH PIPE SUB-ASSEMBLY (for AWD) 

    Refer to PROCEDURE - Step 36

  19. REMOVE OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 37

  20. REMOVE OIL STRAINER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 38

  21. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 4

  22. REMOVE NO. 1 OIL PIPE 

    Refer to PROCEDURE - Step 21

  23. REMOVE NO. 2 OIL PIPE 

    Refer to PROCEDURE - Step 22

  24. REMOVE FUEL TUBE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19

  25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 33

  26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 32

  27. REMOVE SPARK PLUG TUBE GASKET 

    Refer to PROCEDURE - Step 34

  28. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY 
    1. Remove the bolt and wire harness clamp bracket.
      GTY402891Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 25 bolts and 2 nuts.
      GTY409821Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the timing chain or belt cover sub-assembly by prying between the timing chain or belt cover sub-assembly and cylinder head sub-assembly, cylinder head LH or cylinder block sub-assembly with a screwdriver.
      GTY469234Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Protective Tape
      NOTE:

      Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder head LH, cylinder block sub-assembly and timing chain or belt cover sub-assembly.

      HINT: 

      Tape the screwdriver tip before use.

    4. Remove the gasket.
      GTY213852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL 
    1. Using a screwdriver and wooden block, pry out the timing gear case or timing chain case oil seal.
      GTY470464Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Protective Tape
      *2 Wooden Block
      NOTE:

      Be careful not to damage the timing chain or belt cover sub-assembly and oil pump rotor set.

      HINT: 

      Tape the screwdriver tip before use.

scientia non olet · About LEMON Manuals