LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> IS 350 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 140 (Charging System (2GR-FSE) - Service Information) >> Generator >> Removal [04/2013 - 10/2017] >> Procedure

Removal [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [04/2013 - 08/2015] , or refer to PRECAUTION [08/2015 - 10/2016] , or refer to PRECAUTION [10/2016 - 10/2017]

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [04/2013 - 06/2014] , or refer to INITIALIZATION [06/2014 - 08/2015] , or refer to INITIALIZATION [08/2015 - 10/2016] , or refer to INITIALIZATION [10/2016 - 10/2017]

  3. REMOVE V-RIBBED BELT 

    Refer to REMOVAL [04/2013 - 10/2017]

  4. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 4 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 4 [08/2015 - 10/2017]

  5. REMOVE NO. 1 RADIATOR HOSE 
    1. Slide the 2 clips and remove the No. 1 radiator hose.
      GTY462219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE NO. 2 ENGINE COVER 

    Refer to PROCEDURE - Step 2

  7. REMOVE COOLING FAN ECU 
    1. Disconnect the 3 cooling fan ECU connectors.
      GTY462226Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 screws and cooling fan ECU.
  8. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 12

  9. DISCONNECT WIRE HARNESS 
    1. Disconnect the VVT sensor connector and camshaft timing oil control valve assembly connector.
      GTY466890Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 3 nuts and disconnect the wire harness.
  10. REMOVE GENERATOR ASSEMBLY 
    1. Remove the terminal cap.
      GTY457167Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Terminal Cap
    2. Remove the bolt and disconnect the engine wire bracket.
    3. Remove the nut and disconnect the engine wire.
    4. Disconnect the generator assembly connector, and detach the 2 clamps.
    5. Remove the nut, and disconnect the generator bracket.
      GTY458167Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the 2 bolts and generator assembly.
      GTY398398Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the bolt and generator bracket.
      GTY462228Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the bolt and wire harness bracket.
    9. Using an E6 "TORX" socket wrench, remove the stud bolt.
      GTY462229Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals