LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 42 (Engine Starting System (A25A-FKS) - Service Information) >> Engine Switch >> Removal [08/2021 - ] >> Procedure

Removal [08/2021 - ]: Procedure

WARNING: This page is about a different car, the 2024 Lexus ES 250, 2023 Lexus ES 250, 2022 Lexus ES 250, and 2021 Lexus ES 250. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column) 

    Refer to PROCEDURE - Step 2 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 2 [09/2022 - ]

  2. REMOVE FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 4 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 4 [09/2022 - ]

  3. REMOVE COWL SIDE TRIM BOARD LH 

    Refer to PROCEDURE - Step 5 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 5 [09/2022 - ]

  4. REMOVE FRONT DOOR OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 6 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 6 [09/2022 - ]

  5. REMOVE INSTRUMENT SIDE PANEL LH 

    Refer to PROCEDURE - Step 14 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 14 [09/2022 - ]

  6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 15 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 15 [09/2022 - ]

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 16 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 16 [09/2022 - ]

  8. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  9. REMOVE COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  10. REMOVE FRONT DOOR OPENING TRIM COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  11. REMOVE INSTRUMENT SIDE PANEL RH 

    Refer to PROCEDURE - Step 22 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 22 [09/2022 - ]

  12. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 26 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 26 [09/2022 - ]

  13. REMOVE NO. 2 INSTRUMENT CLUSTER MOULDING 

    Refer to PROCEDURE - Step 29 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 29 [09/2022 - ]

  14. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Headup Display) 

    Refer to PROCEDURE - Step 30 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 30 [09/2022 - ]

  15. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Headup Display) 

    Refer to PROCEDURE - Step 31 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 31 [09/2022 - ]

  16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY 

    Refer to PROCEDURE - Step 9

  17. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 8 Inch Display) 

    Refer to PROCEDURE - Step 33 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 33 [09/2022 - ]

  18. REMOVE MULTI-DISPLAY ASSEMBLY WITH CLOCK (for 8 Inch Display) 

    Refer to PROCEDURE - Step 3

  19. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 12.3 Inch Display) 

    Refer to PROCEDURE - Step 35 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 35 [09/2022 - ]

  20. REMOVE MULTI-DISPLAY ASSEMBLY WITH CLOCK (for 12.3 Inch Display) 

    Refer to PROCEDURE - Step 5

  21. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH 

    Refer to PROCEDURE - Step 37 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 37 [09/2022 - ]

  22. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 40 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 40 [09/2022 - ]

  23. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH 

    Refer to PROCEDURE - Step 42 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 42 [09/2022 - ]

  24. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 

    Refer to PROCEDURE - Step 24

  25. REMOVE SWITCH BASE 

    Refer to PROCEDURE - Step 54 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 54 [09/2022 - ]

  26. REMOVE ENGINE SWITCH 
    1. Insert a screwdriver at the position shown in the illustration and detach the 2 claws and remove the engine switch.

      HINT: 

      Tape the screwdriver tip before use.

      GTY817710Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
scientia non olet · About LEMON Manuals