LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 116 (Engine Cooling System (A25A-FXS) - Service Information) >> Radiator >> Installation [06/2018 - ] >> Procedure

Installation [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL LOWER RADIATOR SUPPORT 
    1. Install the 2 lower radiator supports to the radiator assembly.
  2. INSTALL RADIATOR SUPPORT CUSHION 
    1. Install the 2 radiator support cushions to the radiator assembly.
  3. INSTALL RADIATOR ASSEMBLY 
    1. Engage the 2 guides.
    2. Engage the 2 claws to install the fan with motor assembly to the radiator assembly.
      NOTE:

      Do not damage the radiator assembly when installing the fan with motor assembly.

    3. Install the radiator assembly with the fan with motor assembly to the vehicle body.
      NOTE:

      Do not apply excessive force to the cooler condenser assembly or pipe when installing the radiator assembly with the fan with motor assembly.

    4. Engage the 2 guides.
    5. Engage the 2 claws to install the cooler condenser assembly to the radiator assembly.
      NOTE:

      Make sure not to damage the cooler condenser assembly when installing the cooler condenser assembly.

    6. Engage the wire harness clamp.
      GTY768609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Connect the cooling fan motor connector and rotate the lever to lock it.
      NOTE:
      • When connecting the cooling fan motor connector, make sure that the connecting parts of the cooling fan motor connector are free of dirt, water or other foreign matter.
      • Be sure to securely connect the cooling fan motor connector.
    8. Engage the wire harness clamp.
    9. Connect the cooling fan motor connector.
    10. Engage the 4 clamps to connect the wire harness to the fan with motor assembly.
  4. INSTALL NO. 3 INVERTER COOLING HOSE 
    1. Install the No. 3 inverter cooling hose to the radiator assembly and slide the clip to secure it.
    2. Engage the clamp to connect the No. 3 inverter cooling hose to the fan with motor assembly.
  5. CONNECT NO. 2 RADIATOR HOSE 
    1. Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.
    2. Engage the clamp to connect the No. 2 radiator hose to the fan with motor assembly.
  6. CONNECT NO. 2 INVERTER COOLING HOSE 
    1. Engage the clamp and connect the No. 2 inverter cooling hose to the fan with motor assembly.
  7. CONNECT NO. 5 INVERTER COOLING HOSE 
    1. Engage the 2 clamps and connect the No. 5 inverter cooling hose to the fan with motor assembly.
  8. CONNECT NO. 4 INVERTER COOLING HOSE 
    1. Connect the No. 4 inverter cooling hose to the radiator assembly and slide the clip to secure it.
  9. CONNECT NO. 1 RADIATOR HOSE 
    1. Connect the No. 1 radiator hose to the radiator assembly and slide the clip to secure it.
    2. Engage the clamp to connect the No. 1 radiator hose to the fan with motor assembly.
  10. CONNECT NO. 6 WATER BY-PASS HOSE 
    1. Connect the No. 6 water by-pass hose to the radiator assembly.
  11. CONNECT NO. 5 WATER BY-PASS HOSE 
    1. Connect the No. 5 water by-pass hose to the radiator assembly and slide the clip to secure it.
  12. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY 
    1. Install the upper radiator support sub-assembly with the 4 bolts.

      Torque: 12.5 N.m (127 kgf/cm, 9 ft.lbf) 

    2. Engage the 4 clamps to connect the wire harness to the upper radiator support sub-assembly.
    3. Engage the clamp to connect the hood lock control cable assembly to the upper radiator support sub-assembly.
  13. INSTALL NO. 1 RADIATOR AIR GUIDE RH 
    1. Engage the guide and claw.
    2. Install the No. 1 radiator air guide RH with the clip.
  14. INSTALL NO. 1 RADIATOR AIR GUIDE LH 
    1. Engage the guide and claw.
    2. Install the No. 1 radiator air guide LH with the clip.
  15. INSTALL UPPER RADIATOR MOUNTING BRACKET 
    1. Install the 2 upper radiator mounting brackets with the 2 bolts and 2 nuts.

      Torque: 12.5 N.m (127 kgf/cm, 9 ft.lbf) 

    2. Connect the 2 horn connectors.
  16. INSTALL INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 18

  17. INSTALL HOOD LOCK ASSEMBLY 

    Refer to PROCEDURE - Step 9 [06/2018 - 08/2020] , or refer to PROCEDURE - Step 9 [08/2020 - ]

  18. INSTALL VEHICLE APPROACHING SPEAKER ASSEMBLY 

    Refer to INSTALLATION [06/2018 - 08/2020] , or refer to INSTALLATION [08/2020 - 08/2021] , or refer to INSTALLATION [08/2021 - ]

  19. INSTALL RADIATOR SHUTTER SUB-ASSEMBLY 

    Refer to INSTALLATION [06/2018 - 08/2021] , or refer to INSTALLATION [08/2021 - ]

  20. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 3 [08/2021 - ]

  21. INSTALL NO. 2 FRONT BUMPER MOUNTING BRACKET 

    Refer to PROCEDURE - Step 4 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 4 [08/2021 - ]

  22. INSTALL FRONT BUMPER ENERGY ABSORBER 

    Refer to PROCEDURE - Step 5 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 5 [08/2021 - ]

  23. INSTALL HEADLIGHT ASSEMBLY 

    for LED Type Turn Signal Light: Refer to INSTALLATION [06/2018 - ]

    for Bulb Type Turn Signal Light: Refer to INSTALLATION [06/2018 - ]

  24. INSTALL INVERTER WATER PUMP ASSEMBLY 

    Refer to INSTALLATION [06/2018 - ]

  25. ADD ENGINE COOLANT (for Engine) 

    Refer to PROCEDURE - Step 2

  26. INSPECT FOR COOLANT LEAK (for Engine) 

    Refer to PROCEDURE - Step 1

  27. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 42 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 43 [08/2021 - ]

  28. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 43 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 44 [08/2021 - ]

  29. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 45 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 46 [08/2021 - ]

  30. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 44 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 45 [08/2021 - ]

scientia non olet · About LEMON Manuals