LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 300 F Sport >> Repair and Diagnosis >> Engine Mechanical >> Lubrication System >> Engine Lubrication System (2GR-FSE) - Service Information >> Oil Pump >> Removal [09/2014 - 11/2017] >> Procedure

Removal [09/2014 - 11/2017]: Procedure

  1. INSTALL ENGINE TO ENGINE STAND 

    Refer to REMOVAL [09/2014 - 10/2015] , or refer to REMOVAL [10/2015 - 11/2017]

  2. REMOVE ENGINE WIRE 

    Refer to PROCEDURE - Step 20

  3. REMOVE FUEL PUMP ASSEMBLY (for High Pressure) 

    Refer to REMOVAL [09/2014 - 11/2017]

  4. REMOVE V-RIBBED BELT 

    Refer to PROCEDURE - Step 1

  5. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 11

  6. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 2WD) 

    Refer to PROCEDURE - Step 7 [09/2014 - 10/2015] , or refer to PROCEDURE - Step 13 [10/2015 - 11/2017]

  7. REMOVE OIL FILTER BRACKET (for AWD) 

    Refer to PROCEDURE - Step 7

  8. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for AWD) 

    Refer to PROCEDURE - Step 9

  9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 12

  10. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  11. REMOVE WATER PUMP PULLEY 

    Refer to PROCEDURE - Step 9

  12. REMOVE NO. 1 ENGINE COVER 

    Refer to PROCEDURE - Step 7

  13. REMOVE INJECTOR DRIVER 

    Refer to PROCEDURE - Step 8

  14. REMOVE NO. 2 ENGINE COVER 

    Refer to PROCEDURE - Step 3

  15. REMOVE WATER INLET 

    Refer to PROCEDURE - Step 10

  16. REMOVE CRANKSHAFT PULLEY 

    Refer to PROCEDURE - Step 4

  17. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 33

  18. REMOVE OIL STRAINER WITH PIPE SUB-ASSEMBLY (for AWD) 

    Refer to PROCEDURE - Step 34

  19. REMOVE OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 35

  20. REMOVE OIL STRAINER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 36

  21. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 6

  22. REMOVE NO. 1 OIL PIPE 

    Refer to PROCEDURE - Step 18

  23. REMOVE NO. 2 OIL PIPE 

    Refer to PROCEDURE - Step 19

  24. REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 17

  25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 31

  26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 30

  27. REMOVE SPARK PLUG TUBE GASKET 

    Refer to PROCEDURE - Step 32

  28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY 
    1. Remove the bolt and wire harness clamp bracket.
      GTY402891Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 25 bolts and 2 nuts.
      GTY409821Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, cylinder head LH or cylinder block sub-assembly with a screwdriver.
      GTY500996Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      NOTE:

      Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder head LH, cylinder block sub-assembly and timing chain cover sub-assembly.

      HINT: 

      Tape the screwdriver tip before use.

    4. Remove the gasket.
      GTY213852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL 
    1. Using a screwdriver and wooden block, pry out the timing gear case or timing chain case oil seal.
      GTY511124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      *b Wooden Block
      NOTE:

      Be careful not to damage the timing chain cover sub-assembly and oil pump rotor set.

      HINT: 

      Tape the screwdriver tip before use.

scientia non olet · About LEMON Manuals