LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> LX 570 >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim (Service Information) >> Roof Headlining >> Removal [08/2018 - ] >> Procedure

Removal [08/2018 - ]: Procedure

  1. OPEN BACK DOOR 
    1. Open the back door before disconnecting the cable from the negative (-) battery terminal, as some procedures are performed with the back door open.
      NOTE:

      The back door cannot be opened after the cable is disconnected from the negative (-) battery terminal.

  2. REMOVE UPPER RADIATOR SUPPORT SEAL 

    Refer to PROCEDURE - Step 3

  3. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Refer to PRECAUTION [09/2015 - ]

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    WARNING:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [09/2015 - 08/2019] Refer to INITIALIZATION [08/2019 - ]

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) 

    Refer to REMOVAL [09/2015 - ]

  6. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat) 

    HINT: 

    Use the same procedures described for the LH side.

  7. REMOVE TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat) 
    1. Remove the tonneau cover assembly.
  8. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. w/o Illumination:
      1. GTY619036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Detach the 7 claws and 4 clips and remove the front door scuff plate LH.

    2. w/ Illumination:
      1. GTY685724Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Detach the 7 claws and 4 clips.

      2. Disconnect the connector and remove the front door scuff plate LH.
  9. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedures described for the LH side.

  10. REMOVE REAR STEP COVER 

    HINT: 

    Use the same procedure for both rear step covers.

    1. w/o Illumination Type Front Door Scuff Plate:
      1. GTY611251Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Detach the 2 claws and remove the rear step cover.

    2. w/ Illumination Type Front Door Scuff Plate:
      1. GTY666272Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Detach the 4 claws and remove the rear step cover.

  11. REMOVE REAR DOOR SCUFF PLATE LH 
    1. w/o Illumination Type Front Door Scuff Plate:
      1. GTY538597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Remove the screw.

      2. Detach the 3 claws and 4 clips and remove the rear door scuff plate LH.
    2. w/ Illumination Type Front Door Scuff Plate:
      1. GTY666268Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Remove the screw.

      2. Detach the 3 claws and 4 clips and remove the rear door scuff plate LH.
  12. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedures described for the LH side.

  13. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE 
    GTY685720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 6 clips and 4 claws and remove the rear floor mat support plate.
  14. REMOVE ASSIST GRIP SUB-ASSEMBLY 

    See step  38

  15. REMOVE FRONT PILLAR GARNISH LH 

    See step  39

  16. REMOVE FRONT PILLAR GARNISH RH 

    See step  40

  17. REMOVE CENTER PILLAR GARNISH COVER LH 

    HINT: 

    • When removing the center pillar garnish cover LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.
    1. GTY611231Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 2 clips and 2 guides and remove the center pillar garnish cover LH.

  18. REMOVE CENTER PILLAR GARNISH COVER RH 

    HINT: 

    Use the same procedures described for the LH side.

  19. REMOVE CENTER LOWER PILLAR GARNISH LH 

    HINT: 

    • When removing the center lower pillar garnish LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.
    1. GTY597507Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the bolt and seat belt anchor.

    2. GTY538595Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 2 claws and 7 clips and remove the center lower pillar garnish LH.

  20. REMOVE CENTER LOWER PILLAR GARNISH RH 

    HINT: 

    • When removing the center lower pillar garnish RH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.
    1. GTY553846Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Disconnect the connector.

    2. Remove the bolt and seat belt anchor.
    3. GTY610882Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 2 claws and 7 clips and remove the center lower pillar garnish RH.

  21. REMOVE REAR ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for both rear assist grip assemblies.

    1. GTY597508Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 4 claws and remove the 2 assist grip plugs.

    2. GTY610854Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip assembly.
  22. REMOVE CENTER PILLAR GARNISH LH 
    GTY538633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the bolt.
    2. Detach the 2 clips and 2 guides.
    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish LH.
  23. REMOVE CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedures described for the LH side.

  24. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK 

    HINT: 

    Use the same procedure for both No. 1 luggage compartment trim hooks.

    1. GTY240898Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the No. 1 luggage compartment trim hook by turning it clockwise.

  25. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Rear No. 2 Seat) 

    HINT: 

    Use the same procedure for both No. 1 tonneau cover holder caps.

    1. Detach the 2 claws and remove the No. 1 tonneau cover holder cap.
      GTY836944Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH 
    GTY561733Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT: 

    When removing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

    1. w/o Rear No. 2 Seat:
      1. Remove the bolt.
        GTY795126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. GTY538634Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 3 claws and remove the outer lap belt anchor cover.

    3. GTY610945Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the bolt and rear No. 1 seat belt anchor.

    4. w/ Rear No. 2 Seat:
      1. Remove the bolt and rear No. 2 seat belt anchor.
        GTY611136Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the screw and clip.
    6. Detach the 19 clips and 2 claws.
    7. Disconnect the thermistor connector and power outlet socket connector, and then remove the front quarter trim panel assembly LH.
      GTY666274Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH 
    GTY602663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT: 

    When removing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

    1. w/o Rear No. 2 Seat:
      1. Remove the bolt.
        GTY795124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. GTY538636Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 3 claws and remove the outer lap belt anchor cover.

    3. GTY538621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the bolt and rear No. 1 seat belt anchor.

    4. w/ Rear No. 2 Seat:
      1. Detach the 3 claws and remove the outer lap belt anchor cover.
        GTY538622Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt and rear No. 2 seat belt anchor.
        GTY610984Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the screw and clip.
    6. Detach the 17 clips and 2 claws.
    7. Disconnect each connector and then remove the front quarter trim panel assembly RH.
      GTY684367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. REMOVE REAR FRONT QUARTER TRIM GARNISH LH 
    GTY538792Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the screw.
    2. Detach the clip and 2 guides.
    3. Pass the seat belt anchor through the rear front quarter trim garnish LH, and remove the rear front quarter trim garnish LH.
  29. REMOVE REAR FRONT QUARTER TRIM GARNISH RH 

    HINT: 

    Use the same procedures described for the LH side.

  30. REMOVE REAR UPPER PILLAR GARNISH LH 
    1. w/ Rear No. 2 Seat:
      1. Using a moulding remover B, detach the 2 claws and open the seat belt shoulder anchor cover.
        GTY121098Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt and seat belt shoulder anchor.
        GTY611364Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. GTY597554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 5 clips and remove the rear upper pillar garnish LH.

  31. REMOVE CENTER BACK DOOR GARNISH 

    Refer to PROCEDURE - Step 4

  32. REMOVE BACK DOOR SIDE GARNISH RH 

    Refer to PROCEDURE - Step 7

  33. DISCONNECT POWER BACK DOOR ROD 

    Refer to PROCEDURE - Step 8

  34. REMOVE REAR UPPER PILLAR GARNISH RH 
    1. w/ Rear No. 2 Seat:
      1. Using a moulding remover, detach the 2 claws and open the seat belt shoulder anchor cover.
        GTY114764Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt and seat belt shoulder anchor.
        GTY686009Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 5 clips.
      GTY826062Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Power Back Door Rod
    3. Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish RH.
  35. REMOVE MAP LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  36. REMOVE NO. 1 ROOM LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  37. REMOVE NO. 3 ROOM LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  38. REMOVE VISOR BRACKET COVER 

    HINT: 

    Use the same procedure for both visor bracket covers.

    1. GTY228375Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 4 claws and remove the visor bracket cover.

      NOTE:

      Visor bracket cover cannot be reused.

  39. REMOVE VISOR ASSEMBLY LH 
    GTY228377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 screws and visor assembly LH.
  40. REMOVE VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedures described for the LH side.

  41. REMOVE VISOR HOLDER 

    HINT: 

    Use the same procedure for both visor holders.

    1. GTY138218Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.
  42. REMOVE CENTER VISOR ASSEMBLY LH 
    GTY793354Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    * a Protective Tape
    * b Cover
    1. Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor assembly LH.

      HINT: 

      Tape the screwdriver tip before use.

  43. REMOVE CENTER VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedures described for the LH side.

  44. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Pre-collision System) 

    Refer to PROCEDURE - Step 1

  45. REMOVE RAIN SENSOR COVER 

    Refer to PROCEDURE - Step 1

  46. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System) 

    Refer to PROCEDURE - Step 1

  47. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System) 

    Refer to PROCEDURE - Step 2

  48. REMOVE SEAT BELT ANCHOR COVER (w/ Rear No. 2 Seat) 
    GTY611609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.
  49. REMOVE ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for both assist grip assemblies.

    1. GTY803832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Cutout

      Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

      • SST: 09813-00010 
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      HINT: 

      Use the same procedure for the LH side and RH side.

    2. Pull SST as shown in the illustration to detach the claw.
      GTY812140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a 30 to 45°
      NOTE:

      To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

      HINT: 

      • Use the same procedure for the claw on the other side of the assist grip cover LH.
      • Use the same procedure for the LH side and RH side.
    3. Remove the assist grip cover LH.

      HINT: 

      Use the same procedure for the LH side and RH side.

    4. Detach the 2 clips as shown in the illustration to remove the assist grip assembly.
      GTY824839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 2 clips from the vehicle body.
  50. REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH 
    GTY793570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    * a Cutout
    1. Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
      • SST: 09813-00010 
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      HINT: 

      Use the same procedure for the LH side and RH side.

    2. Pull SST as shown in the illustration to detach the claw.
      GTY832546Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a 30 to 45°
      NOTE:

      To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

      HINT: 

      • Use the same procedure for the claw on the other side of the assist grip cover LH.
      • Use the same procedure for the LH side and RH side.
    3. Remove the assist grip cover LH.

      HINT: 

      Use the same procedure for the LH side and RH side.

    4. Detach the 2 clips as shown in the illustration to remove the No. 2 assist grip assembly LH.
      GTY838190Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 2 clips from the vehicle body.
  51. REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH 

    HINT: 

    Use the same procedures described for the LH side.

  52. REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for both 3rd seat assist grip assemblies.

    1. GTY800893Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Cutout

      Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

      • SST: 09813-00010 
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      HINT: 

      Use the same procedure for the LH side and RH side.

    2. Pull SST as shown in the illustration to detach the claw.
      GTY807643Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a 30 to 45°
      NOTE:

      To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

      HINT: 

      • Use the same procedure for the claw on the other side of the assist grip cover LH.
      • Use the same procedure for the LH side and RH side.
    3. Remove the assist grip cover LH.

      HINT: 

      Use the same procedure for the LH side and RH side.

    4. Detach the 2 clips as shown in the illustration to remove the 3rd seat assist grip assembly.
      GTY824840Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 2 clips from the vehicle body.
  53. REMOVE ROOF HEADLINING ASSEMBLY 
    GTY613298Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT: 

    • When removing the roof headlining assembly, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.
    • After moving the seats, disconnect the cable from the negative (-) battery terminal.
    1. GTY544318Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      w/o Pre-collision System:

      Disconnect the connector.

    2. GTY544319Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Disconnect the connector.

    3. w/ Pre-collision System:
      1. w/o Camera Heater:
        GTY544316Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect the 2 connectors.

      2. w/ Camera Heater:
        GTY691495Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Disconnect the 3 connectors.

    4. GTY538796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Disconnect the connector.

    5. GTY804489Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Front Left Side
      * b Washer Hose

      Disconnect the 3 roof wire connectors and washer hose.

    6. Detach the 4 clamps.
    7. GTY796983Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Front Right Side

      Remove the bolt.

    8. Disconnect the antenna cord connector and detach the 2 clamps.
    9. GTY781470Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Rear Right Side

      Disconnect the antenna cord connector.

    10. GTY808560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Rear Left Side

      Disconnect the washer hose.

    11. w/ Rear No. 2 Seat:
      1. Detach the 12 claws, 2 clips, 2 guides and 16 fasteners.
        GTY802510Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        * a Guide - -
    12. w/o Rear No. 2 Seat:
      1. Detach the 12 claws, 3 clips, 2 guides and 16 fasteners.
        GTY831448Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        * a Guide - -
    13. GTY115969Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the roof headlining assembly from the rear of the vehicle as shown in the illustration.

      NOTE:

      Be careful not to damage the roof headlining assembly when taking it out.

  54. REMOVE FRONT ROOF SIDE RAIL GARNISH LH 
    GTY817424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    * a Cut Off Position
    1. Detach the 3 clips.
    2. Cut off the 3 clips and remove the front roof side rail garnish LH.
    3. Remove the 3 clips from the vehicle body.
  55. REMOVE FRONT ROOF SIDE RAIL GARNISH RH 

    HINT: 

    Use the same procedures described for the LH side.

  56. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
    GTY115911Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the front door opening trim weatherstrip LH.
  57. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedures described for the LH side.

  58. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 
    GTY115912Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the rear door opening trim weatherstrip LH.
  59. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedures described for the LH side.

  60. REMOVE BACK DOOR WEATHERSTRIP 
    GTY141995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the back door weatherstrip.

      HINT: 

      Remove any remaining sealer from the vehicle body.

  61. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH 
    GTY835685Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    * a Protective Tape
    1. Put protective tape around the front door scuff plate outside LH.
    2. Detach the 4 clips and remove the front door scuff plate outside LH.
  62. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE RH 

    HINT: 

    Use the same procedures described for the LH side.

  63. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH 
    GTY834300Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    * a Protective Tape
    1. Put protective tape around the rear door scuff plate outside LH.
    2. Detach the 3 clips and remove the rear door scuff plate outside LH.
  64. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH 

    HINT: 

    Use the same procedures described for the LH side.

  65. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH 
    GTY115901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 6 claws of the front shoulder belt anchor plate sub-assembly LH, and slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.
  66. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedures described for the LH side.

  67. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH 
    GTY610883Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 6 claws and remove the rear shoulder belt anchor plate sub-assembly LH.
  68. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedures described for the LH side.

  69. REMOVE ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat) 
    GTY611685Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 7 claws and remove the roof side inner garnish cover LH.
  70. REMOVE ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat) 

    HINT: 

    Use the same procedures described for the LH side.

  71. REMOVE REAR NO. 1 SEAT SHOULDER BELT HANGER 

    HINT: 

    Use the same procedure for both rear No. 1 seat shoulder belt hangers.

    1. GTY831017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      * a Spring Nut

      Remove the 2 spring nuts and rear No. 1 seat shoulder belt hanger.

  72. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat) 
    GTY809019Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    * a Spring Nut
    1. Remove the 2 spring nuts and rear No. 2 seat shoulder belt hanger LH.
  73. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat) 

    HINT: 

    Use the same procedures described for the LH side.

  74. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH 
    GTY818632Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *1 Rear No. 7 side air duct
    *2 Rear No. 8 side air duct
    1. Remove the 8 screws and rear No. 7 side air duct and rear No. 8 side air duct.
    2. GTY122974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the 7 screws.

    3. Detach the 4 claws and remove the quarter trim cover sub-assembly LH.
  75. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH 
    GTY122973Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 7 screws.
    2. Detach the 4 claws and remove the quarter trim cover sub-assembly RH.
  76. REMOVE NO. 2 CUP HOLDER (w/ Rear No. 2 Seat) 
    1. Remove the 5 screws.
      GTY115898Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 3 claws and remove the No. 2 cup holder.
  77. REMOVE TONNEAU COVER HOLDER BRACKET LH (w/o Rear No. 2 Seat) 
    1. Remove the 5 screws.
      GTY777297Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Quarter Trim Base LH
    2. Remove the 3 screws and the detach front quarter trim base LH.
    3. Detach the 3 claws and remove the tonneau cover holder bracket LH.
  78. REMOVE TONNEAU COVER HANGER LH (w/o Rear No. 2 Seat) 
    1. Remove the 2 screws and the detach tonneau cover hanger LH and rear quarter trim base LH.
      GTY797844Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Quarter Trim Base LH
  79. REMOVE NO. 1 CUP HOLDER (w/ Rear No. 2 Seat) 
    GTY122979Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 5 screws.
    2. Detach the 3 claws and remove the No. 1 cup holder.
  80. REMOVE TONNEAU COVER HOLDER BRACKET RH (w/o Rear No. 2 Seat) 
    1. Remove the 5 screws.
      GTY782570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Quarter Trim Base RH
    2. Remove the 3 screws and the detach front quarter trim base RH.
    3. Detach the 3 claws and remove the tonneau cover holder bracket RH.
  81. REMOVE TONNEAU COVER HANGER RH (w/o Rear No. 2 Seat) 
    1. Remove the 2 screws and the detach tonneau cover hanger RH and rear quarter trim base RH.
      GTY804120Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Quarter Trim Base RH
  82. REMOVE NO. 1 SIDE TRIM BASE COVER LH 
    GTY602787Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 4 claws and remove the No. 1 side trim base cover LH.
  83. REMOVE NO. 1 SIDE TRIM BASE COVER RH 
    GTY793200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *1 Rear No. 4 side air duct
    *2 Rear No. 5 side air duct
    1. Remove the 6 screws and rear No. 4 side air duct and rear No. 5 side air duct.
    2. GTY588444Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Detach the 4 claws and remove the No. 1 side trim base cover RH.

  84. REMOVE NO. 2 SIDE TRIM BASE COVER LH 
    GTY562281Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 4 claws and remove the No. 2 side trim base cover LH.
  85. REMOVE NO. 2 SIDE TRIM BASE COVER RH 

    HINT: 

    Use the same procedures described for the LH side.

  86. REMOVE FOLD SEAT SWITCH ASSEMBLY (w/ Rear No. 2 Seat) 
    GTY685989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 6 claws and remove the fold seat switch assembly.
  87. REMOVE QUARTER TRIM COVER RH (w/o Rear No. 2 Seat) 
    1. Detach the 6 claws and remove the quarter trim cover RH.
      GTY823812Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  88. REMOVE QUARTER TRIM COVER LH 
    GTY625711Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 6 claws and remove the quarter trim cover LH.
  89. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH 
    1. Remove the quarter trim lid sub-assembly RH.
  90. REMOVE SIDE TRIM BOX COVER (w/o Woofer) 
    1. Remove the side trim box cover.
  91. REMOVE SIDE TRIM BOX (w/o Woofer) 
    GTY679925Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 9 screws and side trim box.
scientia non olet · About LEMON Manuals