LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> IS 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 144 (Automatic Transmission System (Aa81E, For 2GR-FKS) - Diagnostic Codes (2 Of 4)) >> AUTOMATIC TRANSMISSION SYSTEM (for 2GR-FKS) >> DTC P0775-7F: Pressure Control Solenoid "B" Actuator Stuck Off [10/2017 - 09/2019] >> Procedure

DTC P0775-7F: Pressure Control Solenoid "B" Actuator Stuck Off [10/2017 - 09/2019]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus IS 350, 2023 Lexus IS 350, 2022 Lexus IS 350, 2021 Lexus IS 350, and 2020 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Transmission / Trouble Codes.

      Powertrain > Transmission > Trouble Codes 

    5. Read the DTCs using the Techstream.

      Result

      Result Proceed to
      Only DTCs P0770-7F, P0775-7F and P2713-7F are output A
      Only DTC P0775-7F is output B
      P0770-7F, P0775-7F, P2713-7F and other DTCs are output C

      HINT: 

      If any DTCs other than P0770-7F, P0775-7F and P2713-7F are output, perform troubleshooting for those DTCs first.

    Result: 

    B 

    See step  12

    Result: 

    C 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2017 - 09/2018]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2018 - 09/2019] 

    Result: 

    A 

    See step  2

  2. CLEAR DTC AND PERFORM STALL SPEED TEST 
    1. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [10/2017 - ]

      Powertrain > Transmission > Clear DTCs 

      HINT: 

      Write down the currently output DTCs before clearing them.

    2. Perform the stall speed test.

      Refer to MECHANICAL SYSTEM TESTS [10/2017 - 09/2020]

      Result

      Result Proceed to
      Stall speed test can be performed A
      Stall speed test cannot be performed B

    Result: 

    B 

    See step  11

    Result: 

    A 

    See step  3

  3. CLEAR DTC AND PERFORM RUNNING TEST 
    1. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [10/2017 - ]

      Powertrain > Transmission > Clear DTCs 

      HINT: 

      Write down the currently output DTCs before clearing them.

    2. Start the engine, drive the vehicle and perform the inspection.

      Result

      Result Proceed to
      • Gear cannot be shifted between 1st gear and 4th gear
      • Gear can only be shifted from 4th gear to 5th gear
      • Gear cannot be shifted between 5th gear and 8th gear*
      		 A
      • Gear can be shifted from 1st gear to 4th gear
      • For 5th gear and above, gear shifts to neutral
      		 B
      Conditions other than those listed above C

      HINT: 

      *: If the gear is shifted to 5th gear or above, gear shifts will no longer be able to be performed. When performing the test again, first clear the DTCs.

    Result: 

    B 

    See step  12

    Result: 

    C 

    See step  7

    Result: 

    A 

    See step  4

  4. INSPECT SHIFT SOLENOID VALVE SR 
    1. Remove the shift solenoid valve SR.
      GTY654436Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Shift Solenoid Valve SR

      Refer to DISASSEMBLY [04/2013 - ]

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Terminal of shift solenoid valve SR connector - Shift solenoid valve SR body 20°C (68°F) 11 to 15 Ω
    3. Connect a positive (+) lead from the battery to the terminal of the shift solenoid valve connector, and a negative (-) lead to the shift solenoid valve body. Check that the valve moves and makes an operating sound.

      OK

      Valve moves and makes an operating sound.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SHIFT SOLENOID VALVE SR. Refer to  COMPONENTS [10/2016 - ] 

    Result: 

    OK 

    See step  5

  5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY 
    1. Check the transmission valve body assembly.

      Refer to REMOVAL [10/2016 - ]

      OK

      There is no foreign matter on each valve and they operate smoothly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY. Refer to  COMPONENTS [10/2016 - ] 

    Result: 

    OK 

    See step  6

  6. INSPECT TORQUE CONVERTER ASSEMBLY 
    1. Check the torque converter assembly.

      Refer to INSPECTION [10/2017 - ]

      OK

      The torque converter assembly operates normally.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY. Refer to  COMPONENTS [10/2016 - ] 

    Result: 

    NG 

    REPLACE TORQUE CONVERTER ASSEMBLY. Refer to  COMPONENTS [10/2016 - ] 

  7. CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NC3 TERMINAL) 
    1. Disconnect the F73 transmission wire connector.
      GTY806390Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Transmission Wire)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F73-12 (NC3O) - Body ground Always 99 to 101 Ω
    3. Turn the engine switch on (IG).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      F73-11 (NC3B) - Body ground Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  8

  8. INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC3)) 
    1. Disconnect the transmission revolution sensor (NC3) connector.
      GTY645665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Transmission Revolution Sensor (NC3))
      *b Component without harness connected
      (Transmission Wire)

      Refer to REMOVAL [04/2013 - ]

    2. Disconnect the F73 transmission wire connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Terminal 1 of the transmission revolution sensor (NC3) connector - 11 (NC3B) Always Below 1 Ω
      Terminal 2 of the transmission revolution sensor (NC3) connector - 12 (NC3O) Always Below 1 Ω
      Terminal 1 of the transmission revolution sensor (NC3) connector or 11 (NC3B) - Body ground Always 10 kΩ or higher
      Terminal 2 of the transmission revolution sensor (NC3) connector or 12 (NC3O) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TRANSMISSION REVOLUTION SENSOR (NC3). Refer to  COMPONENTS [04/2013 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE TRANSMISSION WIRE. Refer to  COMPONENTS [04/2013 - ] 

  9. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) 
    1. Disconnect the F73 transmission wire connector.
    2. Disconnect the F102 ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F73-11 (NC3B) - F102-78 (NC3B) Always Below 1 Ω
      F73-12 (NC3O) - F102-110 (NC3O) Always Below 1 Ω
      F73-11 (NC3B) or F102-78 (NC3B) - Body ground Always 10 kΩ or higher
      F73-12 (NC3O) or F102-110 (NC3O) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  10

  10. REPLACE ECM 
    1. Replace the ECM.

      Refer to COMPONENTS [10/2017 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    PERFORM A/T CODE REGISTRATION. Refer to  REGISTRATION [10/2017 - ] 

  11. INSPECT SHIFT SOLENOID VALVE SLT 
    1. Remove the shift solenoid valve SLT.
      GTY677581Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Shift Solenoid Valve SLT

      Refer to DISASSEMBLY [04/2013 - ]

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SLT - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK

      Valve moves and makes an operating sound.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  5

    Result: 

    NG 

    REPLACE SHIFT SOLENOID VALVE SLT. Refer to  COMPONENTS [10/2016 - ] 

  12. INSPECT SHIFT SOLENOID VALVE SL2 
    1. Remove the shift solenoid valve SL2.
      GTY635585Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Shift Solenoid Valve SL2

      Refer to DISASSEMBLY [04/2013 - ]

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SL2 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK

      Valve moves and makes an operating sound.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  5

    Result: 

    NG 

    REPLACE SHIFT SOLENOID VALVE SL2. Refer to  COMPONENTS [10/2016 - ] 

scientia non olet · About LEMON Manuals