DTC P2714: Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) [11/2021 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / ECT / Trouble Codes.

   Powertrain > ECT > Trouble Codes 

5. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   Only DTC P2714 is output	A
   P2714 and one or more of the following DTCs are output: P0746, P0771, P0776, P0796, P2808, P2817	B
   P0746, P0771, P0776, P0796, P2714, P2808 or P2817 and other DTCs are output	C

   HINT: 

   If any DTCs other than P0746, P0771, P0776, P0796, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.

Result: 

B 

See step  5

Result: 

C 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2021 - ] 

Result: 

A 

See step  2

1. Remove the shift solenoid valve SLT.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Shift Solenoid Valve SLT)

   Refer to DISASSEMBLY [11/2021 - ]

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Terminal 1 of the shift solenoid valve SLT - terminal 2	20°C (68°F)	5.0 to 5.6 Ω

3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

   OK

   Valve moves and makes an operating sound.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SLT. Refer to  COMPONENTS [11/2021 - ] 

Result: 

OK 

See step  3

1. Check the transmission valve body assembly.

   Refer to REMOVAL [11/2021 - ]

   OK

   There is no foreign matter on each valve and they operate smoothly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY. Refer to  COMPONENTS [11/2021 - ] 

Result: 

OK 

See step  4

1. Check the torque converter assembly.

   Refer to INSPECTION [11/2021 - ]

   OK

   The torque converter operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY. Refer to  COMPONENTS [11/2021 - ] 

Result: 

NG 

REPLACE TORQUE CONVERTER ASSEMBLY. Refer to  COMPONENTS [11/2021 - ] 

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / ECT / Trouble Codes.

   Powertrain > ECT > Trouble Codes 

5. Check if DTCs other than P2714 are output.

   Result

   Result	Proceed to
   P2714 and P0746 are output	A
   P2714, P0771 and P0776 are output P2714 and P0776 are output	B
   P2714, P0771 and P0796 are output P2714 and P0796 are output P2714, P0796 and P2808 are output	C
   P2714 and P2808 are output	D
   P2714 and P2817 are output	E

Result: 

A 

GO TO DTC P0746 FLOWCHART. Refer to  DTC P0746: Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) [11/2021 - ] 

Result: 

B 

GO TO DTC P0776 FLOWCHART. Refer to  DTC P0776: Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) [11/2021 - ] 

Result: 

C 

GO TO DTC P0796 FLOWCHART. Refer to  DTC P0796: Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) [11/2021 - ]  

Result: 

D 

GO TO DTC P2808 FLOWCHART. Refer to  DTC P2808: Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) [11/2021 - ]  

Result: 

E 

GO TO DTC P2817 FLOWCHART. Refer to  DTC P2817: Pressure Control Solenoid "H" Performance or Stuck OFF (Shift Solenoid Valve SL5) [11/2021 - ]