Parking Brake Assembly: Disassembly

REMOVE REAR WHEEL
SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
1. Remove the 2 bolts and separate the rear disc brake caliper assembly.
HINT:

Do not disconnect the flexible hose from the rear disc brake caliper assembly.

Fig 1: Locating Rear Disc Brake Caliper Assembly With Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE REAR DISC
1. Release the parking brake.
2. Put matchmarks on the rear disc and the axle hub.
  
  Fig 2: Aligning Matchmarks On Rear Disc And Axle Hub
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Remove the rear disc.
HINT:

If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns smoothy.

Fig 3: Turning Shoe Adjuster Until Wheel Turns Smoothy
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE SHOE STRUT
1. Using needle-nose pliers, remove the 2 parking brake shoe return tension No. 1 springs.
2. Remove the parking brake shoe strut and parking brake shoe strut compression spring.
Fig 4: Identifying Parking Brake Shoe Return Tension No. 1 Springs
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE NO. 1 SHOE ASSEMBLY
1. Remove the parking brake shoe hold down spring No. 1 cup, parking brake shoe hold down spring and parking brake shoe hold down spring No. 2 cup.
2. 2WD:
  Remove the parking brake shoe hold down spring No. 1 pin.
3. Disconnect the parking brake shoe return tension No. 2 spring and remove the parking brake No. 1 shoe assembly.
Fig 5: Identifying Parking Brake No. 1 Shoe Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET
1. Remove the parking brake shoe adjusting screw set.
2. Remove the parking brake shoe return tension No. 2 spring.
Fig 6: Identifying Shoe Adjusting Screw Set And Return Tension No. 2 Spring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE NO. 2 SHOE ASSEMBLY
1. Remove the parking brake shoe hold down spring No. 1 cup, parking brake shoe hold down spring and parking brake shoe hold down spring No. 2 cup.
2. 4WD:
  Remove the parking brake shoe hold down spring No. 2 pin.
3. Remove the parking brake No. 2 shoe assembly.
  
  Fig 7: Identifying Parking Brake No. 2 Shoe Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Using needle-nose pliers, disconnect the parking brake No. 3 cable assembly from the parking brake cable shoe lever.
NOTE: Be careful not to damage parking brake No. 3 cable assembly.

Fig 8: Disconnecting Parking Brake No. 3 Cable
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE SHOE GUIDE PLATE
1. Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.
SEPARATE PARKING BRAKE NO. 3 CABLE ASSEMBLY (See REMOVAL )
DISCONNECT SKID CONTROL SENSOR WIRE (for 2WD) (See REMOVAL )
REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD) (See REMOVAL )
REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING NO. 2 PIN (for 2WD)
1. Remove the parking brake shoe hold down spring No. 2 pin from the backing plate.
SEPARATE REAR SPEED SENSOR (for 4WD) (See REMOVAL )
REMOVE REAR AXLE SHAFT NUT (for 4WD) (See REMOVAL )
REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD) (See REMOVAL )
REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING NO. 1 PIN (for 4WD)
1. Remove the parking brake shoe hold down spring No. 1 pin from the backing plate.
Fig 11: Locating Parking Brake Shoe Hold Down Spring No. 1 Pin
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE SHOE LEVER
1. Using a screwdriver, remove the C-washer.
2. Remove the shim and parking brake shoe lever from the parking brake No. 2 shoe assembly.

Fig 12: Removing C-Washer