Rear Seat Outer Belt Assembly With PRETENSIONER: Installation

WARNING: This page is about a different car, the 2008 Lexus IS F. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY
1. Check the degree of the tilt when the ELR begins to lock
  1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt while gently pulling the belt.
    NOTE: Do not disassemble the retractor.
    
    Fig 1: Checking Degree Of Tilt When ELR Begins To Lock
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Temporarily install the rear seat 3 point type belt assembly with the 2 bolts.
3. Fully tighten the rear side bolt first, then the front side bolt to install the rear seat 3 point type belt assembly
  Torque:
  
  For front bolt
  
  7.5 N*m (77 kgf*cm, 66 in.*lbf)
  
  For rear bolt
  
  42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  Fig 2: Identifying Rear Seat 3 Point Type Belt Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the pretensioner connector and lock the locking button as shown in the illustration.
  
  Fig 3: Identifying Pretensioner Connector And Locking Button
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
1. Pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.
2. Engage the 3 clips and 5 claws to install the package tray trim panel assembly.
  
  Fig 4: Identifying Clips And Claws Of Package Tray Trim Panel Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Engage the 4 claws to install the rear seat shoulder belt cover LH
  HINT
  
  Use the same procedures for the RH side and the LH side.
  
  Fig 5: Identifying Rear Seat Shoulder Belt Cover LH Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the floor end of the rear seat 3 point type belt assembly LH with the bolt
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap protruding parts of the floor panel.
  
  HINT
  
  Use the same procedure for the RH side and the LH side
5. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly
    
    Fig 6: Identifying Protruding Parts Of Floor Panel
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CENTER STOP LIGHT SET (See INSTALLATION )
INSTALL ROOF SIDE INNER GARNISH LH (See INSTALLATION )
INSTALL ROOF SIDE INNER GARNISH RH (See INSTALLATION )
INSTALL REAR SEAT SIDE GARNISH LH (See INSTALLATION )
INSTALL REAR SEAT SIDE GARNISH RH (See INSTALLATION )
INSTALL REAR DOOR SCUFF PLATE LH (See INSTALLATION )
INSTALL REAR DOOR SCUFF PLATE RH (See INSTALLATION )
INSTALL REAR SEATBACK ASSEMBLY (See INSTALLATION )
INSTALL REAR SEAT CUSHION ASSEMBLY (See INSTALLATION )
INSTALL REAR SEAT HEADREST ASSEMBLY LH
INSTALL REAR SEAT HEADREST ASSEMBLY RH
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: Some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
INSPECT SRS WARNING LIGHT
Inspect the SRS warning light (See DIAGNOSIS SYSTEM ).