LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> IS 250 RWD, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 176 (Engine Control System (2GR-FSE) - System And Component Testing, On-Vehicle Inspection, Removal, Inspection & Installation) >> Camshaft Timing Oil Control Valve Assembly >> Removal

Camshaft Timing Oil Control Valve Assembly: Removal

WARNING: This page is about a different car, the 2008 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE COOL AIR INTAKE DUCT SEAL  (See REMOVAL )
  2. REMOVE ENGINE ROOM SIDE COVER LH  (See REMOVAL )
  3. REMOVE ENGINE ROOM SIDE COVER RH  (See REMOVAL )
  4. REMOVE V-BANK COVER SUB-ASSEMBLY  (See REMOVAL )
  5. REMOVE FRONT FENDER PROTECTOR UPPER RH  (See REMOVAL )
  6. REMOVE FRONT FENDER PROTECTOR UPPER LH  (See REMOVAL )
  7. REMOVE ROOF DRIP SIDE FINISH MOLDING RH  (See REMOVAL )
  8. REMOVE ROOF DRIP SIDE FINISH MOLDING LH  (See REMOVAL )
  9. REMOVE FRONT WIPER ARM HEAD CAP  (See REMOVAL )
  10. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH  (See REMOVAL )
  11. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH  (See REMOVAL )
  12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  (See REMOVAL )
  13. DRAIN ENGINE COOLANT  (See ON-VEHICLE INSPECTION )
  14. REMOVE NO. 2 VENTILATION HOSE  (See REMOVAL )
  15. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE  (See REMOVAL )
  16. REMOVE THROTTLE BODY  (See REMOVAL )
  17. REMOVE INTAKE AIR SURGE TANK  (See REMOVAL )
  18. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Exhaust Side) 
    1. Disconnect the oil control valve connector.
    2. Remove the bolt and oil control valve.
    3. Remove the O-ring from the oil control valve.
    Fig 1: Locating Oil Control Valve Connector And Bolt
    G05285330Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Intake Side) 
    1. Remove the bolt and V-bank cover bracket.
      Fig 2: Locating V-Bank Cover Bracket And Bolt
      G05285331Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the oil control valve connector.
    3. Remove the bolt and oil control valve.
    4. Remove the O-ring from the oil control valve.
    Fig 3: Locating Oil Control Valve Connector And Bolt
    G05285332Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Intake Side) 
    1. Disconnect the oil control valve connector.
    2. Remove the bolt and oil control valve.
    3. Remove the O-ring from the oil control valve.
    Fig 4: Locating Oil Control Valve Connector And Bolt
    G05285333Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Exhaust Side) 
    1. Disconnect the wiring harness to the bracket.
    2. Remove the bolt and bracket.
      Fig 5: Locating Camshaft Timing Oil Control Valve Wiring Harness Bracket And Bolt
      G05285334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the oil control valve connector.
    4. Remove the bolt and oil control valve.
    5. Remove the O-ring from the oil control valve.
    Fig 6: Locating Oil Control Valve Connector And Bolt
    G05285333Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals