Front Wiper Motor: Removal

REMOVE COOL AIR INTAKE DUCT SEAL (See REMOVAL )
REMOVE ENGINE ROOM SIDE COVER LH (See REMOVAL )
REMOVE ENGINE ROOM SIDE COVER RH (See REMOVAL )
REMOVE FRONT UPPER FENDER PROTECTOR LH
1. Using a clip remover, separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.
2. Disengage the 3 clips and the claw to remove the front upper fender protector LH.
REMOVE FRONT UPPER FENDER PROTECTOR RH
HINT:

Use the same procedures for the RH side and the LH side.

Fig 1: Identifying Front Upper Fender Protector Clips And Claw
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE ROOF DRIP SIDE FINISH MOLDING LH (See REMOVAL )
REMOVE ROOF DRIP SIDE FINISH MOLDING RH
HINT:

Use the same procedures for the RH side and the LH side.
REMOVE FRONT WIPER ARM HEAD CAP
1. Using a screwdriver, remove the front wiper arm head cap.
  HINT:
  - Use the same procedures for the RH side and the LH side.
  - Tape the screwdriver tip before use.
  Fig 2: Removing Front Wiper Arm Head Cap
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
1. Remove the nut and the front wiper arm and blade assembly LH.
Fig 3: Locating Front Wiper Arm And Blade Nut LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
1. Remove the nut and the front wiper arm and blade assembly RH.
Fig 4: Locating Front Wiper Arm And Blade Nut RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
1. Remove the 2 clips.
  
  Fig 5: Identifying Cowl Top Ventilator Louver Sub-Assembly With Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disengage the 11 claws, and pull out the cowl top ventilator louver sub-assembly.
Fig 6: Pulling Out Cowl Top Ventilator Louver Sub-Assembly
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
1. Disconnect the connector.
2. Remove the 2 bolts.
  
  Fig 7: Locating Windshield Wiper Motor With Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Disengage the rubber pin of the windshield wiper motor from the vehicle body as shown in the illustration. Remove the windshield wiper motor and link assembly.
Fig 8: Disengaging Rubber Pin Of Windshield Wiper Motor From Vehicle Body
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
1. Using a screwdriver, separate the windshield wiper No. 2 link rod from the crank arm pivot of the front wiper motor assembly as shown in the illustration.
  HINT:
  
  Tape the screwdriver tip before use.
  
  Fig 9: Separating Windshield Wiper No. 2 Link Rod
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a screwdriver, separate the windshield wiper No. 1 link rod from the pivot of the front wiper link assembly as shown in the illustration.
  HINT:
  
  Tape the screwdriver tip before use.
  
  Fig 10: Separating Windshield Wiper No. 1 Link Rod
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Position the windshield wiper No. 1 link rod as shown in the illustration. Using a screwdriver, remove the windshield wiper No. 1 link rod.
  HINT:
  
  Tape the screwdriver tip before use.
  
  Fig 11: Removing Windshield Wiper No. 1 Link Rod
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Using a "torx" socket wrench (T30), remove the 2 bolts and the windshield wiper motor assembly from the wind shield wiper link assembly.