LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2017 >> QX30 Base >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> LAN System (Can) >> DTC/Circuit Diagnosis >> Body Can Communication 1 >> Diagnosis Procedure

Diagnosis Procedure

  1. ERROR ECU CONFIRMATION

    Confirm whether there is error in one ECU or plural ECU on CAN diagnosis function with CONSULT.

    Is error in one ECU or plural ECU?

    One ECU 

    GO TO STEP 2  .

    Plural ECU 

    GO TO STEP 3  .

  2. CHECK ECU CIRCUIT

    Check a circuit for applicable ECU. Refer to following.

    Unit name Circuit Reference
    A/C auto amp. Circuit between the CAN potential distributor electrical connector (Body) and the A/C auto amp. DIAGNOSIS PROCEDURE 
    BCM Circuit between the CAN potential distributor electrical connector (Body) and the BCM (Body Control Module) DIAGNOSIS PROCEDURE 
    CAN gateway Circuit between the CAN potential distributor electrical connector (Body) and the CAN gateway DIAGNOSIS PROCEDURE 
    Combination meter Circuit between the CAN potential distributor electrical connector (Body) and the combination meter DIAGNOSIS PROCEDURE 
    Driver seat control unit Circuit between the CAN potential distributor electrical connector (Body) and the driver seat control unit DIAGNOSIS PROCEDURE 
    Electronic ignition switch control unit Circuit between the CAN potential distributor electrical connector (Body) and the electronic ignition switch control unit DIAGNOSIS PROCEDURE 
    Intelligent Key unit Circuit between the CAN potential distributor electrical connector (Body) and the Intelligent Key unit DIAGNOSIS PROCEDURE 
    Passenger seat control unit Circuit between the CAN potential distributor electrical connector (Body) and the passenger seat control unit DIAGNOSIS PROCEDURE 
    Right front door control unit Circuit between the CAN potential distributor electrical connector (Body) and the right front door control unit DIAGNOSIS PROCEDURE 

    Is the inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Repair or replace applicable parts.

  3. CHECK CAN CIRCUIT VOLTAGE

    1. Turn ignition switch ON.
    2. Check voltage between CAN potential distributor electrical connector (Body) harness connector each terminals.
      Terminals Voltage
      (Approx.)
      + -
      CAN potential distributor electrical connector (Body)
      Terminal Terminal
      CAN-H Ground 2.5 - 2.7 V
      CAN-L Ground 2.1 - 2.3 V
      CAN-H CAN-L 0.2 - 0.4 V

    Is the inspection result normal?

    YES 

    Check intermittent incident. Refer to INTERMITTENT INCIDENT .

    NO 

    GO TO STEP 4  .

  4. CHECK HARNESS CONNECTOR CONDITION

    1. Turn ignition switch OFF.
    2. Check each harness connector connected to CAN potential distributor electrical connector for proper connection, locking, loose contact, damage, contamination and corrosion.

    Is the inspection result normal?

    YES 

    GO TO STEP 5  .

    NO 

    Securely connects or repair the harness connectors.

  5. CHECK CAN POTENTIAL DISTRIBUTOR ELECTRICAL CONNECTOR

    1. Turn ignition switch OFF.
    2. Disconnect all of harness connector from CAN potential distributor electrical connector (Body).
    3. Check CAN potential distributor electrical connector (Body). Refer to COMPONENT INSPECTION [CAN POTENTIAL DISTRIBUTOR ELECTRICAL CONNECTOR (BODY)] .

    Is the inspection result normal?

    YES 

    GO TO STEP 6  .

    NO 

    Replace CAN potential distributor electrical connector (Body).

  6. POSSIBLE CAUSE CONFIRMATION

    1. Turn ignition switch ON.
    2. Check the voltage between CAN potential distributor electrical connector (Body) terminals (CAN-H and CAN-L).
      NOTE:

      [Recommend] Check CAN potential distributor electrical connector (Body) terminals that harness connector is not connected.

    3. Disconnect each harness connector from CAN potential distributor electrical connector (Body) one by one.
    4. Check the voltage change when the harness connector just disconnected.
      Terminals Condition Voltage
      (Approx.)
      + -
      CAN potential distributor electrical connector (Body)
      Terminal Terminal
      CAN-H CAN-L When the harness connector just disconnected. No change

    Is the inspection result normal?

    YES 

    Check intermittent incident. Refer to INTERMITTENT INCIDENT .

    NO 

    GO TO STEP 7  .

  7. CHECK SHORT CIRCUIT

    Check the possible cause circuit for short to battery or ground.

    Unit name Circuit Reference
    A/C auto amp. Circuit between the CAN potential distributor electrical connector (Body) and the A/C auto amp. DIAGNOSIS PROCEDURE 
    BCM Circuit between the CAN potential distributor electrical connector (Body) and the BCM (Body Control Module) DIAGNOSIS PROCEDURE 
    CAN gateway Circuit between the CAN potential distributor electrical connector (Body) and the CAN gateway DIAGNOSIS PROCEDURE 
    Combination meter Circuit between the CAN potential distributor electrical connector (Body) and the combination meter DIAGNOSIS PROCEDURE 
    Driver seat control unit Circuit between the CAN potential distributor electrical connector (Body) and the driver seat control unit DIAGNOSIS PROCEDURE 
    Electronic ignition switch control unit Circuit between the CAN potential distributor electrical connector (Body) and the electronic ignition switch control unit DIAGNOSIS PROCEDURE 
    Intelligent Key unit Circuit between the CAN potential distributor electrical connector (Body) and the Intelligent Key unit DIAGNOSIS PROCEDURE 
    Passenger seat control unit Circuit between the CAN potential distributor electrical connector (Body) and the passenger seat control unit DIAGNOSIS PROCEDURE 
    Right front door control unit Circuit between the CAN potential distributor electrical connector (Body) and the right front door control unit DIAGNOSIS PROCEDURE 

    Is the inspection result normal?

    YES 

    Replace applicable ECU.

    NO 

    Repair or replace harness.

scientia non olet · About LEMON Manuals