Lighting System
- Precautions
- Headlamp - Xenon Type -
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - H/LAMP -
- Terminals and Reference Values for BCM
- Terminals and Reference Values for IPDM E/R
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- CONSULT-II Functions (BCM)
- CONSULT-II Functions (IPDM E/R)
- Headlamp Does Not Change To High Beam (Both Sides)
- Headlamp Does Not Change To High Beam (One Side)
- Headlamp Low Beam Does Not Illuminate (Both Sides)
- Headlamp Low Beam Does Not Illuminate (One Side)
- Headlamp RH Low Beam and High Beam Does Not Illuminate
- Headlamp LH Low Beam and High Beam Does Not Illuminate
- Headlamps Do Not Turn OFF
- General Information for Xenon Headlamp Trouble Diagnosis
- Caution:
- Xenon Headlamp Trouble Diagnosis
- Aiming Adjustment
- Bulb Replacement
- Removal and Installation
- Disassembly and Assembly
- Daytime Light System
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - DTRL -
- Terminals and Reference Values for BCM
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- Inspection Parking Brake Switch
- CONSULT-II Functions (BCM)
- Consult-II Basic Operation
- Daytime Light Control Does Not Operate Properly
- Aiming Adjustment
- Bulb Replacement
- Removal and Installation
- Disassembly and Assembly
- Auto Light System
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Major Components and Functions
- Schematic
- Wiring Diagram - AUTO/L -
- Terminals and Reference Values for BCM
- Terminals and Reference Values for IPDM E/R
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- CONSULT-II Functions (BCM)
- CONSULT-II Functions (IPDM E/R)
- Symptom Chart
- Lighting Switch Inspection
- Optical sensor System Inspection
- Removal and Installation of Optical Sensor
- Headlamp Aiming Control
- Front Fog Lamp
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Wiring Diagram - F/FOG -
- Terminals and Reference Values for BCM
- Terminals and Reference Values for IPDM E/R
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- CONSULT-II Functions (BCM)
- CONSULT-II Functions (IPDM E/R)
- Front Fog Lamps Do Not Illuminate (Both Sides)
- Front Fog Lamp Does Not Illuminate (One Side)
- Aiming Adjustment
- Bulb Replacement
- Removal and Installation
- Turn Signal And Hazard Warning Lamps
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - TURN -
- Terminals and Reference Values for BCM
- Terminals and Reference Value for Rear Combination Lamp Control Unit
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- CONSULT-II Functions (BCM)
- Turn Signal Lamp Does Not Operate
- Rear Turn Signal Lamp Does Not Operate
- Hazard Warning Lamp Does Not Operate But Turn Signal Lamp Operate
- Bulb Replacement (Front Turn Signal Lamp)
- Bulb Replacement (Rear Turn Signal Lamp)
- Removal and Installation of Front Turn Signal Lamp
- Removal and Installation of Rear Turn Signal Lamp
- Removal and Installation of Rear Combination Lamp Control Unit
- Headlamp Switch And Turn Signal Switch
- Hazard Switch
- Combination Switch
- Stop Lamp
- Back-Up Lamp
- Parking, License Plate And Tail Lamps
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - TAIL/L -
- Terminals and Reference Values for BCM
- Terminals and Reference Values for IPDM E/R
- Terminals and Reference Value for Rear Combination Lamp Control Unit
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- CONSULT-II Functions (BCM)
- CONSULT-II Functions (IPDM E/R)
- Parking, License Plate and Side Marker Lamps Do Not Illuminate
- Tail Lamp Does Not Operate
- Parking, License Plate, Side Maker and Tail Lamps Do Not Turn OFF (After Approx. 10 Minutes)
- License Plate Lamp
- Front Parking Lamp
- Tail Lamp
- Front Side Marker Lamp
- Rear Side Marker Lamp
- Rear Combination Lamp Control Unit
- Rear Combination Lamp
- Interior Room Lamp
- Component Parts and Harness Connector Location
- System Description
- Schematic
- Wiring Diagram - ROOM/L -
- Terminals and Reference Values for BCM
- How to Proceed With Trouble Diagnosis
- Preliminary Check
- CONSULT-II Functions (BCM)
- Interior Room Lamp Control Does Not Operate
- Map Lamp Control Does Not Operate
- Personal Lamp Control Does Not Operate
- Ignition Key Hole Illumination Control Does Not Operate
- All Step Lamps Do Not Operate
- All Interior Room Lamps Do Not Operate
- Bulb Replacement
- Removal and Installation
- Illumination
- Bulb Specifications