LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 372 (Front Drive Axle) >> Repair Instructions >> Front Differential Drive Pinion Gear Yoke Replacement >> Installation Procedure

Installation Procedure

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Installing Oil Seal
    GM664080Courtesy of GENERAL MOTORS CORP.
  1. Install the oil seal by doing the following:
    1. Position the oil seal over the seal bore.
    2. Install the J 36366  over the oil seal.
    3. Strike the Special Tool J 36366  with a hammer until the seal flange seats on the axle housing surface.
  2. Apply sealant GM P/N 12346004 (Canadian P/N 10953480) or equivalent to the splines of the drive pinion yoke.
  3. Install the pinion yoke.

    Align the reference marks made during removal.

    4. CAUTION:

    Refer to Pinion Flange/Yoke Installation Caution .

  4. Seat the pinion yoke onto the pinion shaft by tapping it with a soft-faced hammer until a few pinion shaft threads show through the yoke.
  5. Install the washer and a new pinion nut.
    6. Fig 2: Holding Pinion Flange Using Special Tool
    GM664065Courtesy of GENERAL MOTORS CORP.
  6. Install the J 8614-01 onto the pinion yoke as shown.
    7. CAUTION:

    Refer to Fastener Caution .

    NOTE:

    If the rotating torque is exceeded, the pinion will have to be removed and a new collapsible spacer installed.

  7. Tighten the pinion nut while holding the J 8614-01 .

    Tighten 

    Tighten the pinion nut until the pinion end play is just taken up. Rotate the pinion while tightening the nut to seat the bearings.

  8. Measure the rotating torque of the pinion using an inch-pound torque wrench.

    Compare the measurement with the rotating torque recorded earlier.

    Tighten 

    Tighten the pinion nut, in small increments, as needed, until the torque required in order to rotate the pinion is 0.40-0.57 N.m (3-5 lb in) greater than the torque recorded during removal.

  9. Once the specified torque is obtained, rotate the pinion several times to ensure the bearings have seated. Recheck the rotating torque and adjust if necessary.
    10. Fig 3: Front Axle Pinion Yoke, Propeller Shaft Universal Joint, Yoke Retainer And Bolts
    GM363785Courtesy of GENERAL MOTORS CORP.
  10. Install the propeller shaft universal joint (2) to the pinion yoke (1).

    Align the reference marks made during removal.

  11. Install the yoke retainers (7) and the yoke retainer bolts (6) to the pinion yoke (1).

    Tighten 

    Tighten the yoke retainer bolts to 25 N.m (18 lb ft).

  12. Inspect the axle lubricant level, and add, if necessary. Refer to Front Axle Lubricant Level Inspection (9.25 Inch Axle) , Front Axle Lubricant Level Inspection (8.25 Inch Axle) .
  13. Install the brake calipers. Refer to Front Brake Caliper Replacement (1500 Series) , Front Brake Caliper Replacement (2500 Series) .
  14. Fill the drive axle. Refer to Front Axle Lubricant Replacement .
  15. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
  16. Lower the vehicle.
scientia non olet · About LEMON Manuals