Pinpoint Test D: B1368:11, B1368:15

Refer to ADJUSTABLE PEDAL for schematic and connector information.

Normal Operation and Fault Conditions

The adjustable pedal motor contains a Hall-effect sensor allowing the DSM to monitor the adjustable pedal position. The DSM stores the sensor information and uses this information when a memory position is recalled using the memory SET switch, a RKE transmitter or a passive ignition key. When 1 or more of the following Diagnostic Trouble Codes (DTCs) is set, the adjustable pedals enter a "jog mode". When the pedals are in jog mode, the memory system recall does not function from the memory SET switch, RKE transmitter or passive ignition key. When in jog mode and the adjustable pedal control switch is pressed, the motor moves the pedals for 2 seconds in the direction selected regardless of the length of time the switch is actually pressed.

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
DSM B1368:11	Adjustable Pedal Position Feedback Sensor: Circuit Short To Ground	This DTC sets in continuous memory or on demand if the Hall-effect feedback voltage is less than 3.5 volts or the Hall-effect monitor voltage is greater than or equal to 6.85 volts.
DSM B1368:15	Adjustable Pedal Position Feedback Sensor: Circuit Short To Battery Or Open	This DTC sets in continuous memory or on demand if the DSM detects battery voltage or open on the Hall-effect switch feedback circuit.

Possible Sources

Wiring, terminals or connectors
Adjustable pedal motor

NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may cause damage to the connector

D1 CHECK THE HALL-EFFECT CIRCUITS FOR AN OPEN

Ignition OFF.

Disconnect adjustable pedal motor C2159.

Disconnect DSM C341E.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2159 Pin 3	Courtesy of FORD MOTOR COMPANY	C341E Pin 20
C2159 Pin 4	Courtesy of FORD MOTOR COMPANY	C341E Pin 15

Are the resistances less than 3 ohms?

Yes

GO to D2

No	REPAIR the circuit.

D2 CHECK THE HALL-EFFECT CIRCUITS FOR A SHORT TO GROUND

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2159 Pin 3	Courtesy of FORD MOTOR COMPANY	Ground Pin -
C2159 Pin 4	Courtesy of FORD MOTOR COMPANY	Ground Pin -

Are the resistances greater than 10, 000 ohms?

Yes

GO to D3

No	REPAIR the circuit.

D3 CHECK THE HALL-EFFECT CIRCUITS FOR A SHORT TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2159 Pin 3	Courtesy of FORD MOTOR COMPANY	C2159 Pin 4

Is the resistance greater than 10, 000 ohms?

Yes

GO to D4

No	REPAIR the circuit.

D4 CHECK THE HALL-EFFECT CIRCUITS FOR A SHORT TO VOLTAGE

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2159 Pin 3	Courtesy of FORD MOTOR COMPANY	Ground Pin -
C2159 Pin 4	Courtesy of FORD MOTOR COMPANY	Ground Pin -

Is any voltage present?

Yes	REPAIR the circuit.

CHECK for other DSM Diagnostic Trouble Codes (DTCs). If other Diagnostic Trouble Codes (DTCs) are present, GO to the DTC Chart: DSM.If no other DSM Diagnostic Trouble Codes (DTCs) are present, the system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.SET the ignition to OFF. DISCONNECT all in-line electrical connectors between the DSM and the adjustable pedal motor.INSPECT DSM C341E, adjustable pedal motor C2159 and in-line electrical connectors for corrosion, bent pins and pushed-out pins. REPAIR the connectors as necessary.