Pinpoint Test L: Poor Image Quality - Vehicles With 360 Degree Camera

NOTE: Before disconnecting any of the cameras, verify the connectors are properly seated and latched.

Refer to PARKING AID for schematic and connector information.

Normal Operation and Fault Conditions

The video signals are transmitted from each camera to the IPMB on a coaxial cable. The IPMB processes the image data and sends a single video image to the APIM on shielded, twisted pair circuits. REFER to: Parking Aid - System Operation and Component Description .

Possible Sources
- Dirty or scratched camera lens
- Fuse
- Wiring, terminals or connectors
- Coaxial cable
- Camera
- IPMB
- APIM concern
Visual Inspection and Pre-checks
- Inspect the camera lenses for damage, dirt, debris and scratches.

L1 INSPECT THE CAMERA IMAGES

Ignition ON.

Press the camera selection switch.

Courtesy of FORD MOTOR COMPANY

NOTE: F-150 shown, other vehicles similar.

Inspect the 360 degree view image to determine which camera image(s) is/are affected.

1
- Front camera
2
- LH side camera
3
- RH side camera
4
- Rear camera

Does the poor image quality affect more than one camera image?

Yes

GO to L18

No	* For a front camera concern, GO to L2* For a rear camera concern, GO to L6* For a LH side camera concern, GO to L10* For a RH side camera concern, GO to L14

L2 CHECK THE FRONT CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TO VOLTAGE

Ignition OFF.

Disconnect IPMB C2512D.

Disconnect Front parking aid camera C1663.

Ignition ON.

Measure VDC :

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 2	Courtesy of FORD MOTOR COMPANY	Ground
coaxial cable shield at C2512D Pin 2	Courtesy of FORD MOTOR COMPANY	Ground

Is any DC voltage present?

Yes	REPLACE the affected coaxial cable.

GO to L3

L3 CHECK THE FRONT CAMERA COAXIAL CABLE CORE FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 2	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to L4

No	REPLACE the affected coaxial cable.

L4 CHECK THE FRONT CAMERA COAXIAL CABLE CORE AND SHIELD FOR AN OPEN

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 2	Courtesy of FORD MOTOR COMPANY	coaxial cable core at C1663 Pin 1
coaxial cable shield at C2512D Pin 2	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at C1663 Pin 1

Are the resistances less than 3 ohm?

Yes

GO to L5

No	REPLACE the affected coaxial cable.

L5 CHECK THE FRONT CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 2	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at C2512D Pin 2

Is the resistance greater than 10, 000 ohms?

Yes	INSTALL a new front parking aid camera, REFER to: Front Parking Aid Camera . If the concern is still present after camera replacement, GO to L24

No	REPLACE the affected coaxial cable.

L6 CHECK THE REAR CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TO VOLTAGE

Ignition OFF.

Disconnect IPMB C2512D.

Disconnect Rear parking aid camera C4358.

Ignition ON.

Measure VDC :

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 1	Courtesy of FORD MOTOR COMPANY	Ground
coaxial cable shield at the C2512D Pin 1	Courtesy of FORD MOTOR COMPANY	Ground

Is any DC voltage present?

Yes	REPLACE the affected coaxial cable.

GO to L7

L7 CHECK THE REAR CAMERA COAXIAL CABLE CORE FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 1	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to L8

No	REPLACE the affected coaxial cable.

L8 CHECK THE REAR CAMERA COAXIAL CABLE CORE AND SHIELD FOR AN OPEN

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 1	Courtesy of FORD MOTOR COMPANY	coaxial cable core at C4358 Pin 1
coaxial cable shield at the C2512D Pin 1	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at the C4358 Pin 1

Are the resistances less than 3 ohm?

Yes

GO to L9

No	REPLACE the affected coaxial cable.

L9 CHECK THE REAR CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512D Pin 1	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at the C2512D Pin 1

Is the resistance greater than 10, 000 ohms?

Yes	INSTALL a new rear parking aid camera. REFER to: Rear Parking Aid Camera . If the concern is still present after camera replacement, GO to L24

No	REPLACE the affected coaxial cable.

L10 CHECK THE LH (LEFT-HAND) SIDE CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TO VOLTAGE

Ignition OFF.

Disconnect IPMB C2512C.

Disconnect LH side parking aid camera C5104.

Ignition ON.

Measure VDC :

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 1	Courtesy of FORD MOTOR COMPANY	Ground
coaxial cable shield at the C2512C Pin 1	Courtesy of FORD MOTOR COMPANY	Ground

Is any DC voltage present?

Yes	REPLACE the affected coaxial cable.

GO to L11

L11 CHECK THE LH (LEFT-HAND) SIDE CAMERA COAXIAL CABLE CORE FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 1	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to L12

No	REPLACE the affected coaxial cable.

L12 CHECK THE LH (LEFT-HAND) SIDE CAMERA COAXIAL CABLE CORE AND SHIELD FOR AN OPEN

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 1	Courtesy of FORD MOTOR COMPANY	coaxial cable core at C5104 Pin 1
coaxial cable shield at the C2512C Pin 1	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at the C5104 Pin 1

Are the resistances less than 3 ohm?

Yes

GO to L13

No	REPLACE the affected coaxial cable.

L13 CHECK THE LH (LEFT-HAND) SIDE CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 1	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at the C2512C Pin 1

Is the resistance greater than 10, 000 ohms?

Yes	INSTALL a new LH side camera. REFER to: Side Parking Aid Camera . If the concern is still present after camera replacement, GO to L24

No	REPLACE the affected coaxial cable.

L14 CHECK THE RH (RIGHT-HAND) SIDE CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TO VOLTAGE

Ignition OFF.

Disconnect IPMB C2512C.

Disconnect RH side camera C6104.

Ignition ON.

Measure VDC :

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 2	Courtesy of FORD MOTOR COMPANY	Ground
coaxial cable shield at the C2512C Pin 2	Courtesy of FORD MOTOR COMPANY	Ground

Is any DC voltage present?

Yes	REPLACE the affected coaxial cable.

GO to L15

L15 CHECK THE RH (RIGHT-HAND) SIDE CAMERA COAXIAL CABLE CORE FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 2	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to L16

No	REPLACE the affected coaxial cable.

L16 CHECK THE RH (RIGHT-HAND) SIDE CAMERA COAXIAL CABLE CORE AND SHIELD FOR AN OPEN

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 2	Courtesy of FORD MOTOR COMPANY	coaxial cable core at C6104 Pin 1
coaxial cable shield at the C2512C Pin 2	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at the C6104 Pin 1

Are the resistances less than 3 ohm?

Yes

GO to L17

No	REPLACE the affected coaxial cable.

L17 CHECK THE RH (RIGHT-HAND) SIDE CAMERA COAXIAL CABLE CORE AND SHIELD FOR A SHORT TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
coaxial cable core at C2512C Pin 2	Courtesy of FORD MOTOR COMPANY	coaxial cable shield at the C2512C Pin 2

Is the resistance greater than 10, 000 ohms?

Yes	INSTALL a new RH side camera. REFER to: Side Parking Aid Camera . If the concern is still present after camera replacement, GO to L24

No	REPLACE the affected coaxial cable.

L18 CHECK FOR VOLTAGE AT THE IPMB (IMAGE PROCESSING MODULE B)

Ignition OFF.

Disconnect IPMB C2512B.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2512B Pin 1	Courtesy of FORD MOTOR COMPANY	Ground

Is the voltage greater than 11 volts at both pins?

Yes

GO to L19

No	INSPECT BJB fuse 25 (10A). If the fuse is OK, repair the circuit. If the fuse is not OK, REFER to OEM ELECTRICAL WIRING DIAGRAM INTRODUCTION to identify the possible causes of the short circuit.

L19 CHECK FOR GROUND AT THE IPMB (IMAGE PROCESSING MODULE B)

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
IPMB case	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance less than 3 ohms?

Yes

GO to L20

No	REPAIR the ground.

L20 CHECK THE VIDEO SIGNAL AND SHIELD CIRCUITS FOR A SHORT TO VOLTAGE BETWEEN THE IPMB (IMAGE PROCESSING MODULE B) AND APIM (SYNC MODULE)

Disconnect APIM C2383A.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C3676A Pin 5	Courtesy of FORD MOTOR COMPANY	Ground
C3676A Pin 6	Courtesy of FORD MOTOR COMPANY	Ground
C3676A Pin 4	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the circuit in question.

GO to L21

L21 CHECK THE VIDEO SIGNAL CIRCUITS FOR AN OPEN BETWEEN THE IPMB (IMAGE PROCESSING MODULE B) AND APIM (SYNC MODULE)

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C3676A Pin 6	Courtesy of FORD MOTOR COMPANY	C2383A Pin 14
C3676A Pin 5	Courtesy of FORD MOTOR COMPANY	C2383A Pin 15

Are the resistances less than 3 ohms?

Yes

GO to L22

No	REPAIR the circuit in question.

L22 CHECK THE VIDEO SIGNAL CIRCUITS FOR A SHORT TO GROUND BETWEEN THE IPMB (IMAGE PROCESSING MODULE B) AND APIM (SYNC MODULE)

Measure:

Positive Lead	Measurement / Action	Negative Lead
C3676A Pin 6	Courtesy of FORD MOTOR COMPANY	Ground
C3676A Pin 5	Courtesy of FORD MOTOR COMPANY	Ground

Are the resistances greater than 10, 000 ohms?

Yes

GO to L23

No	REPAIR the circuit in question.

L23 CHECK THE VIDEO SIGNAL CIRCUITS FOR A SHORT TO TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
C3676A Pin 6	Courtesy of FORD MOTOR COMPANY	C3676A Pin 5

Is the resistance greater than 10, 000 ohms?

Yes

GO to L24

No	REPAIR the circuits.

L24 CHECK FOR CORRECT IPMB (IMAGE PROCESSING MODULE B) OPERATION

Ignition OFF.

Disconnect and inspect the IPMB and related in-line connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the IPMB and related in-line connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes

CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPMB. REFER to: Image Processing Module B (IPMB) - Vehicles With: Parking Aid Camera . If the concern is still present after IPMB replacement, GO to L25

No	The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.

L25 CHECK FOR CORRECT APIM (SYNC MODULE) OPERATION

Ignition OFF.

Disconnect and inspect the APIM connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the APIM connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, REFER to: Information and Entertainment System - Component Location .

No	The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.