Diagnostic Trouble Code (DTC) Chart
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| ABS | B1111:53 | Electric Park Brake Enable: Deactivated | GO to Pinpoint Test I |
| ABS | B1111:54 | Electric Park Brake Enable: Missing Calibration | GO to Pinpoint Test F |
| ABS | C0609:01 | Park Brake Switch Circuit: General Electrical Failure | GO to Pinpoint Test B |
| ABS | C0616:9A | Park Brake Control Module Control Circuit Performance: Component or System Operating Conditions | GO to Pinpoint Test B |
| ABS | C1034:01 | Park Brake: General Electrical Failure | GO to Pinpoint Test B |
| ABS | C1034:07 | Park Brake: Mechanical Failures | GO to Pinpoint Test B |
| ABS | C1034:13 | Park Brake: Circuit Open | GO to Pinpoint Test B |
| ABS | C1034:25 | Park Brake: Signal Shape/Waveform Failure | GO to Pinpoint Test B |
| ABS | C1034:2F | Park Brake: Signal Erratic | GO to Pinpoint Test B |
| ABS | C1034:47 | Park Brake: Watchdog/Safety μC Failure | GO to Pinpoint Test B |
| ABS | C1034:48 | Park Brake: Supervision Software Failure | GO to Pinpoint Test B |
| ABS | C1034:57 | Park Brake: Invalid/Incompatible Software Component | GO to Pinpoint Test B |
| ABS | C1034:77 | Park Brake: Commanded Position Not Reachable | GO to Pinpoint Test D |
| ABS | C1034:78 | Park Brake: Alignment Or Adjustment Incorrect | GO to Pinpoint Test J |
| ABS | C1034:97 | Park Brake: Component or System Operation Obstructed or Blocked | GO to Pinpoint Test E |
| ABS | C1A43:98 | Motor Supply: Component or System Over Temperature | GO to Pinpoint Test E |
| ABS | C2005:04 | Right Actuator: System Internal Failures | GO to Pinpoint Test H |
| ABS | C2005:1B | Right Actuator: Circuit Resistance Above Threshold | GO to Pinpoint Test E |
| ABS | C2005:71 | Right Actuator: Actuator Stuck | GO to Pinpoint Test E |
| ABS | C2005:74 | Right Actuator: Actuator Slipping | GO to Pinpoint Test C |
| ABS | C2005:77 | Right Actuator: Commanded Position Not Reachable | GO to Pinpoint Test D |
| ABS | C2005:92 | Right Actuator: Performance Or Incorrect Operation | GO to Pinpoint Test A |
| ABS | C2006:04 | Left Actuator: System Internal Failures | GO to Pinpoint Test H |
| ABS | C2006:1B | Left Actuator: Circuit Resistance Above Threshold | GO to Pinpoint Test E |
| ABS | C2006:71 | Left Actuator: Actuator Stuck | GO to Pinpoint Test E |
| ABS | C2006:74 | Left Actuator: Actuator Slipping | GO to Pinpoint Test C |
| ABS | C2006:77 | Left Actuator: Commanded Position Not Reachable | GO to Pinpoint Test D |
| ABS | C2006:92 | Left Actuator: Performance Or Incorrect Operation | GO to Pinpoint Test A |
| ABS | C2007:13 | Right Motor: Circuit Open | GO to Pinpoint Test E |
| ABS | C2007:1C | Right Motor: Circuit Voltage Out Of Range | GO to Pinpoint Test E |
| ABS | C2007:92 | Right Motor: Performance Or Incorrect Operation | GO to Pinpoint Test E |
| ABS | C2007:96 | Right Motor: Component Internal Failure | GO to Pinpoint Test G |
| ABS | C2008:13 | Left Motor: Circuit Open | GO to Pinpoint Test E |
| ABS | C2008:1C | Left Motor: Circuit Voltage Out Of Range | GO to Pinpoint Test E |
| ABS | C2008:92 | Left Motor: Performance Or Incorrect Operation | GO to Pinpoint Test E |
| ABS | C2008:96 | Left Motor: Component Internal Failure | GO to Pinpoint Test G |
| ABS | U2002:00 | Switch: No Sub Type Information | GO to Pinpoint Test L |
| ABS | U2002:47 | Switch: Watchdog/Safety μC Failure | GO to Pinpoint Test B |
| HVAC | B1541:11 | Auto Hold LED: Circuit Short To Ground | GO to Pinpoint Test E |
| HVAC | B1541:15 | Auto Hold LED: Circuit Short To Battery Or Open | GO to Pinpoint Test E |